manualshive.com logo in svg

D&H DH05C, Manual

The D&H DH05C Manual is available for free download on our website. This comprehensive user manual provides clear instructions and helpful tips for operating the DH05C device. Access the manual now at manualshive.com to maximize your product experience and enhance your understanding of its features and functionalities.

Share
Download
background image

2

Fahrzeug-/Funktionsdecoder

 ab Firmware-Version 1.11

2

Contents

1 Introduction .......................................................................................................................................... 4

2 

Safety instructions ............................................................................................................................... 5

3 Warranty ............................................................................................................................................... 5

4 

Support and help.................................................................................................................................. 5

5 

Locomotive decoder DH05C / DH10C / DH12A / DH14B / DH16A / DH18A / DH21A/B /  

 

DH22A/B / PD05A / PD06A / PD12A / PD18A / PD21A ..................................................................... 6

5.1 Functions .............................................................................................................................................. 36
5.1.1  Limitations of the PD series compared to our DH decoder series ....................................................... 37 
5.2 

Installation of the decoder .................................................................................................................... 38

5.3 

Connection of the decoder ................................................................................................................... 39

5.4 

Check after installation ......................................................................................................................... 42

6 

Vehicle function decoder FH05B / FH16A /FH18A / FH22A ............................................................ 43

6.1 Functions .............................................................................................................................................. 50
6.2 

Installation of the vehicle function decoders ........................................................................................ 51

6.3 

Connection of the vehicle function decoders ....................................................................................... 51

6.4 

Check after installation ......................................................................................................................... 53

7 

System format SelecTRIX 1 (SX1) .................................................................................................... 54

7.1 Functions .............................................................................................................................................. 54
7.2 

Setting options ..................................................................................................................................... 54

7.3 Operation.............................................................................................................................................. 57
7.4 

Explication of the brake sections.......................................................................................................... 57

Summary of Contents for DH05C











































































































Reviews:

No comments

Related manuals for DH05C

Perlight Solar PLM-OM Series Installation Manual preview
PLM-OM Series
Brand: Perlight Solar Pages: 19
Generac Power Systems 1.6L 18 kW Owner'S Manual preview
1.6L 18 kW
Brand: Generac Power Systems Pages: 64
Trace Engineering SW II Datasheet preview
SW II
Brand: Trace Engineering Pages: 2
Clearline V210 Manual preview
V210
Brand: Clearline Pages: 4
Cosel AME Series Manual preview
AME Series
Brand: Cosel Pages: 62
Mystery MMD-3007 Service Manual preview
MMD-3007
Brand: Mystery Pages: 36
Avermedia AVerKey550 User Manual preview
AVerKey550
Brand: Avermedia Pages: 38
Vitek VT-3776 Manual Instruction preview
VT-3776
Brand: Vitek Pages: 12
C4i CV-53BI User Manual preview
CV-53BI
Brand: C4i Pages: 9
Vectra Fitness M29 Quick Start Manual preview
M29
Brand: Vectra Fitness Pages: 7
Hoval TopTronic E Solar TTE-SOL Instructions Manual preview
TopTronic E Solar TTE-SOL
Brand: Hoval Pages: 95
DCS Rossini Transport User Manual preview
Rossini Transport
Brand: DCS Pages: 31
Olimpia splendid DC 18 HP Instructions For Installation, Use And Maintenance Manual preview
DC 18 HP
Brand: Olimpia splendid Pages: 144
Patton electronics 2021P Installation And Operation Manual preview
2021P
Brand: Patton electronics Pages: 10
LC HML 210 Operating And Installation Manual preview
HML 210
Brand: LC Pages: 44
ring PowerSourcePro REINVMA10 Instructions Manual preview
PowerSourcePro REINVMA10
Brand: ring Pages: 122
Quonset Microwave QM1003-0.5-18-2 User Manual preview
QM1003-0.5-18-2
Brand: Quonset Microwave Pages: 100
Triotech XBMC Clearstream Quick Start Manual preview
XBMC Clearstream
Brand: Triotech Pages: 16

Brands by name

Popular brands

Load more brands