D&H DH05C Manual Download Page 38 | Manualshive

Page: 38 / 106

background image

38

Fahrzeug-/Funktionsdecoder

ab Firmware-Version 1.11

38

Locomotive/Vehicle function decoder

from firmware version 3.12

The PD06A vehicle decoder for miniature motors is our particularly small vehicle decoder for SX1, SX2 and DCC
operation.

•  No support for MM mode
•  No support of SX1 programming (but SX1 operation is possible through SX2 parameter programming)
•  No SUSI interface
•  No extended function assignments (i.e.: no conditions, no initial mapping etc.)
•  No automatic coupling process
•  No braking with asymmetrical digital voltage and no slow driving
•  No brake ramp

The PD12A, PD18A and PD21A vehicle decoders are particularly inexpensive vehicle decoders for pure DCC
operation and DC analog.

•  No support of the operating modes SX1, SX2 and MM
•  No SUSI interface and no unamplified function outputs
•  No extended function assignments (i.e.: no conditions, no initial mapping etc.)
•  No automatic coupling process (but timers for switching off AUX1 and AUX2 are available)

5.2 Installation of the decoder

Before installation check if the locomotive is in perfect electrical and mechanical condition. Defects and dirt must be
eliminated first. Pay attention to the instructions of the locomotive producer.
Only locomotives running smoothly in analogue mode should be equipped with digital decoder. New locomotives should
be run in at least 30 minutes in each driving direction.

«
...
36
37
38
39
40
...
»

Summary of Contents for DH05C











































































































Reviews:

No comments

Related manuals for DH05C

Brand: lasmex Pages: 10

Brand: NAD Pages: 2

Brand: NAD Pages: 2

Brand: V2 Pages: 48

Brand: C2G Pages: 263

Brand: Ediseja 21 Pages: 22

Grass Valley LUMO

Brand: Belden Pages: 71

Brand: Westermo Pages: 16

Brand: IFM Pages: 35

Brand: S&S Pages: 3

Brand: Phenix Pages: 4

CoolSET ICE2QR 65 Series

Brand: Infineon Pages: 24

Brand: Kübler Pages: 2

CFW-11W G2 RB Series

Brand: WEG Pages: 107

Brand: Parkside Pages: 41

Brand: Thinklogical Pages: 19

USB-4600 Series

Brand: Advantech Pages: 26

Brand: Lindy Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands