D&H DH05C Manual Download Page 70

Page: 70 / 106

Fahrzeug-/Funktionsdecoder

ab Firmware-Version 1.11

Locomotive/Vehicle function decoder

from firmware version 3.12

Name and definition

Range

Standard

145 Conditions for LV

(not relevant to PD*)

Function Value

Default value (always on, if function key on) 0

Only forward

Only ba2

Only while standing

Only while d6

Only at F0 (light) off

Only at F0 (light) on +18

Not in shunting gear

+27

Only in shunting gear

+54

Ignore direction in shunting gear

+81

Ignore driving/stand in shunting gear

+108

Ignore direction and driving/stand in shunting gear +135

Always only one number of each definite range may be added up!

0-161

146 Conditions for LR

(see CV145)

0-161

147 Conditions for AUX1

(see CV145)

0-161

148 Conditions for AUX2

(see CV145)

0-161

149 Conditions for AUX3

(see CV145)

0-161

150 Conditions for AUX4

(see CV145)

0-161

151 Conditions for AUX5

(see CV145)

0-161

152 Conditions for AUX6

(see CV145)

0-161

Summary of Contents for DH05C











































































































Search results

Summary of Contents for DH05C

Reviews:

Related manuals for DH05C

Brands by name

Popular brands

D&H DH05C, Manual

Search results

Summary of Contents for DH05C

Reviews:

Related manuals for DH05C

Brands by name

Popular brands