D&H DH05C Manual Download Page 75 | Manualshive

Page: 75 / 106

background image

75

Fahrzeug-/Funktionsdecoder

ab Firmware-Version 1.11

75

Locomotive/Vehicle function decoder

from firmware version 3.12

Notice to address range:
In MM operation address values from 1 to 255 are allowed. In DCC operation for DCC CV01 only values from 1 to 127 are
allowed. Values from 128 lead to operating the decoder only by MM, i.e. DCC operation is no longer possible. DCC “Service
Mode“ is still possible.

Conversely, activating the long DCC address with CV29/Bit5 means that the decoder can only be operated with DCC. Then
MM operation is no longer possible and MM programming is also disabled. Attention, because “Lock out“ is possible.

9.2 Programming with Märklin central unit 6020/6021

1

‚Short‘

programming allows entering figures between 0 and 79, i.e. in short mode just setup parameters with values

from < 80 can be changed, if the desired value should also be < 80.

2

‚Long‘

programming allows entering figures between 0 and 255, i.e. in long mode all setup parameters with values

from 0 to 255 can be changed. As the display of 6020/6021 alows only binary values, the inserting values must be
devided and entered in two steps.

3 Programming of SUSI parameters Programming of SUSI parameters.

Please notice that 6021/6020 allows only entering values from 01 to 80. Value 0 is missing.

Instead of ‚0‘ always ‚80‘ must be entered.

Changing to programming mode

•  The driving controller must display 0. There may not be other locomotives on the layout.
  Notice the flashing signal of the locomotive!
•  Push STOP and GO button of 6021 simultanously until reset will be triggered (alternatively: disconnect for a
  moment the plug of the transformer). Push STOP button for disconnecting the track power.
•  Enter the current decoder address. If you dont know the address, enter ‚80‘.

«
...
73
74
75
76
77
...
»

Summary of Contents for DH05C











































































































Reviews:

No comments

Related manuals for DH05C

Brand: La Marche Pages: 18

FREQROL-Z200-UL

Brand: Mitsubishi Pages: 120

Brand: MAER IDROPULITRICI Pages: 13

Brand: T-TeleSec Pages: 21

CSI 23KTL-CT/US-480

Brand: CanadianSolar Pages: 88

Brand: Waversasystems Pages: 15

Brand: Icy Box Pages: 30

Brand: Millennia Pages: 2

Brand: IONODES Pages: 23

Brand: Kramer Pages: 17

Brand: Delta Pages: 192

PIKO Inverter 3.0

Brand: Kostal Pages: 15

Brand: Barco Pages: 2

SUNNY HIGHPOWER PEAK1

Brand: SMA Pages: 16

Single Phase Series

Brand: Zeus Appollo Pages: 12

PerfectPower PP150

Brand: Waeco Pages: 44

Brand: DVDO Pages: 9

EXT-DVIDL-2-HDMIR

Brand: Gefen Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands