Daikin VRV IV RKXYQ8T7Y1B Installation And Operation Manual Download Page 36

Page: 36 / 44

12 Operation

Installation and operation manual

8T7Y1B

VRV IV compressor unit for indoor installation

4P408443-1B – 2016.04

12.3.2

To use the dry program (WITHOUT cool/
heat changeover remote control switch)

To start

Press the operation mode selector button on the user interface
several times and select

(program dry operation).

Press the ON/OFF button of the user interface.

Result:

The operation lamp lights up and the system starts

operating.

Press the air flow direction adjust button (only for double-flow,
multi-flow, corner, ceiling-suspended and wall-mounted). Refer
to

"12.4 Adjusting the air flow direction" on page 36

for details.

To stop

Press the ON/OFF button on the user interface once again.

Result:

The operation lamp goes out and the system stops

operating.

NOTICE

Do not turn off power immediately after the unit stops, but
wait for at least 5 minutes.

12.3.3

To use the dry program (WITH cool/heat
changeover remote control switch)

To start

Select cooling operation mode with the cool/heat changeover
remote control switch.

Press the operation mode selector button on the user interface
several times and select

(program dry operation).

Press the ON/OFF button of the user interface.

Result:

The operation lamp lights up and the system starts

operating.

Press the air flow direction adjust button (only for double-flow,
multi-flow, corner, ceiling-suspended and wall-mounted). Refer
to

"12.4 Adjusting the air flow direction" on page 36

for details.

To stop

Press the ON/OFF button on the user interface once again.

Result:

The operation lamp goes out and the system stops

operating.

NOTICE

Do not turn off power immediately after the unit stops, but
wait for at least 5 minutes.

12.4

Adjusting the air flow direction

Refer to the operation manual of the user interface.

12.4.1

About the air flow flap

Double flow+multi-flow units

Corner units

Ceiling suspended units

Wall-mounted units

For the following conditions, a micro computer controls the air flow
direction which may be different from the display.

Cooling

Heating

▪ When the room temperature is

lower

than

the

set

temperature.

▪ When starting operation.

▪ When the room temperature is

higher

than

the

set

temperature.

▪ At defrost operation.

▪ When operating continuously at horizontal air flow direction.

▪ When continuous operation with downward air flow is performed

at the time of cooling with a ceiling-suspended or a wall-mounted
unit, the micro computer may control the flow direction, and then
the user interface indication will also change.

The air flow direction can be adjusted in one of the following ways:

▪ The air flow flap itself adjusts its position.

▪ The air flow direction can be fixed by the user.

▪ Automatic

and desired position .

WARNING

Never touch the air outlet or the horizontal blades while the
swing flap is in operation. Fingers may become caught or
the unit may break down.

NOTICE

▪ The movable limit of the flap is changeable. Contact

your dealer for details. (only for double-flow, multi-flow,
corner, ceiling-suspended and wall-mounted).

▪ Avoid operating in the horizontal direction

. It may

cause dew or dust to settle on the ceiling or flap.

12.5

Setting the master user interface

12.5.1

About setting the master user interface

VRV DX

EKEXV

AHU

In case of VRV DX indoor units

In case of VRV DX indoor units combined with an air
handling unit

Heat exchanger unit

Compressor unit

Refrigerant piping

User interface (dedicated depending on indoor unit type)

VRV DX

VRV direct expansion (DX) indoor unit

EKEXV

Expansion valve kit

AHU

Air handling unit

When the system is installed as shown in the figure above, it is
necessary to designate one of the user interfaces as the master user
interface.

The displays of slave user interfaces show

(change-over

under centralised control) and slave user interfaces automatically
follow the operation mode directed by the master user interface.

Only the master user interface can select heating or cooling mode.

Summary of Contents for VRV IV RKXYQ8T7Y1B












































Search results

Summary of Contents for VRV IV RKXYQ8T7Y1B

Reviews:

Related manuals for VRV IV RKXYQ8T7Y1B

Brands by name

Popular brands

Daikin VRV IV RKXYQ8T7Y1B, Installation And Operation Manual

Search results

Summary of Contents for VRV IV RKXYQ8T7Y1B

Reviews:

Related manuals for VRV IV RKXYQ8T7Y1B

Brands by name

Popular brands