background image

„

English

8

DRAIN PIPING WORK

Caution

Make sure all water is out before making the duct connection.

„

„

„

„

Install the drain piping.

• Make sure the drain works properly.
• The diameter of the drain pipe should be greater than or equal to the 

diameter of the connecting pipe (vinyl tube; pipe size: 20mm;  outer 
dimension: 26mm). (not including the riser)

• Keep the drain pipe short and sloping downwards at a gradient of at 

least 1/100 to prevent air pockets from forming.

Caution

Water accumulating in the drain piping can cause the drain to clog.

• To keep the drain tube from sagging, space hanging wires every 1 to 1.5m.
• Use the drain hose and the metal clamp. Insert the drain hose fully into the drain socket and firmly tighten the metal clamp with 

the upper part of the tape on the hose end. Tighten the metal clamp until the screw head is less than 4mm from the hose.

• The two areas below should be insulated because condensation may form there causing water to leak.

• Drain piping passing indoors
• Drain sockets

Referring the figure below, insulate the 
metal clamp and drain hose using the 
included large sealing pad.

〈〈〈〈

 PRECAUTIONS 

〉〉〉〉

Drain piping connections
• Do not connect the drain piping directly to sewage pipes that smell of ammonia. The ammonia in the sewage might enter the 

indoor unit through the drain pipes and corrode the heat exchanger.

• Do not twist or bend the drain hose, so that excessive force is not applied to it. 

(This type of treatment may cause leaking.)

„

„

„

„

After piping work is finished, check drainage flows smoothly.

• Gradually insert approximately 1L of water into the drain pan to check 

drainage in the manner described below.

• Gradually pour approximately 1L of water from the outlet hole into 

the drain pan to check drainage.

• Check the drainage.

Drain pipe connection hole

Refrigerant piprs

Connect the drain pipe after

removing the rubber cap and

insulation tubing attached to

the connection hole.

4mm

Large sealing pad

Clamp metal

(accessory)

(accessory)

Clamp metal

Drain hose

Tape

(accessory)

Portable pump

Refrigerant pipes

Bucket

Air outlet

Drain outlet

01_EN_3P132003-3K.fm  Page 8  Wednesday, September 28, 2005  3:32 PM

Summary of Contents for Super Multi NX FDKS25EAVMB















Reviews: