background image

88

4. 

Humidifying hose installation work

4-1  Connecting to the indoor unit

• 

Connect the cuff side of the 

G

 humidifying hose to the indoor unit duct.

Duct

Front grille

Cuff

G

   Humidifying 

hose

It is easier to connect the hose 
with the front grille removed.

• 

Left-side piping

Insert as far as possible 
so that there are no gaps.

To pull out the  

G

 humidifying hose to the right side, turn the 

cuff 180° from the position shown in the above illustration.

• 

Left-bottom piping

• 

Left-back piping

Cut the cuff at this point.

Cut the skirt section of the cuff with 
scissors (cut the dotted line section).

Insert the hose into the duct.

4-2  Connecting the cut humidifying hoses

• 

When installing the cut 

G

 humidifying hoses, follow the instructions below.

Insert each 

G

 humidifying hose to the rim 

of the 

J

 joint or an elbow (fi eld supply) so 

that there are no gaps.

Apply the 

K

 binding bands at 10mm from the 

rim of the 

J

 joint or an elbow (fi eld supply) to 

prevent the 

G

 humidifying hose from coming off.

J

 Joint

Elbow

(fi eld supply)

•  Use not more than 1 elbow to ensure humidifying capacity.

4-3 

How to replace the drain plug and drain hose

• 

Replacing onto the left side 

1) 

Remove the insulation fi xing screw on the right to 

remove the drain hose.

2) 

Reattach the insulation fi xing screw on the right as it 

was.
Forgetting to attach this may cause water leakages. 

3)  Remove the drain plug on the left side and attach it to 

the right side. 

4)  Insert the drain hose and tighten with included 

C

 indoor unit fi xing screw.

How to set drain plug

No gap.

Do not apply lubricating oil 
(refrigerant oil) to the drain plug 
when inserting it. 
The application of lubrication oil to 
the drain plug will deteriorate the 
plug to cause drain leakage from 
the plug.

Insert a hexagon wrench (4mm).

Drain hose attachment position

The drain hose is on the back of the unit.

Left side

Right side

Attachment on the left side

Drain hose

C

  Indoor unit 

 fi xing screw

Attachment on the right side 
(factory default)

Drain hose

Insulation fi xing 

screw

 CAUTION

Use caution not to deform the cuff while installing the humidifying hose. Using a deformed cuff may cause a clopping sound.

01_EN_3P338604-1E.indd   8

2/18/2019   14:09:17

Summary of Contents for RXZ25NV1B9























Reviews: