background image

2

3P362438-1B English

1 .  Introduction

1 .1 .  General information

This installation manual concerns the VRV IV, full inverter driven, heat 
pump system.

6

7

6

6

3

3

3

5

4

2

1

8

1  VRV IV Heat pump outdoor unit
2  Refrigerant piping
3  VRV indoor unit
4  Branch Provider unit (required to connect Mini-split indoor 

units)

5  Mini-split indoor units
6  User interface (dedicated depending on indoor unit type)
7  User interface (wireless, dedicated depending on indoor unit 

type)

8  Cool/Heat selector

 INFORMATION

Not all combinations of indoor units are allowed. For guidance, see  

1.2. Combination and options on page 2

1 .2 .  Combination and options

The VRV IV heat pump system can be combined with several types of 
indoor units and is intended for R410A use only.

For an overview which units are available you can consult the product 
catalogue for VRV IV.

 NOTE

To be sure your system setup (outdoor unit + indoor unit(s)) will work, 
you have to consult the latest technical engineering data for VRV IV 
heat pump.

An overview is given indicating the allowed combinations of indoor 
units and outdoor units. Not all combinations are allowed. They are 
subject to rules (combination between outdoor-indoor, single outdoor 
unit use, multiple outdoor unit use, combinations between indoor 
units, etc.) mentioned in the technical engineering data. 

1 .2 .1 .  Indoor unit combinations

In general following type of indoor units can be connected to a VRV 

IV heat pump system. The list is non-exhaustive and depends on both 

outdoor unit model and indoor unit model combinations.

• 

VRV indoor units.

• 

Mini-split indoor units.

• 

AHU (air to air applications): AHU Integration kit is required. See 

latest Engineering Data Book for more details .

1 .2 .2 .  Outdoor unit combinations

Standard combinations for VRV IV heat pump system are as indicated 
in table below, where RXYQ192-408 consists of several RXYQ72-168 
modules as indicated.

72

96

120

144

168

RXYQ72TTJU/TYDN

1

RXYQ96TTJU/TYDN

1

RXYQ120TTJU/TYDN

1

RXYQ144TTJU/TYDN

1

RXYQ168TTJU/TYDN

1

RXYQ192TTJU/TYDN

1

1

RXYQ216TTJU/TYDN

1

1

RXYQ240TTJU/TYDN

2

RXYQ264TTJU/TYDN

1

1

RXYQ288TTJU/TYDN

2

RXYQ312TTJU/TYDN

1

1

RXYQ336TTJU/TYDN

2

RXYQ360TTJU/TYDN

3

RXYQ384TTJU/TYDN

1

1

1

RXYQ408TTJU/TYDN

1

1

1

To install the outdoor unit, the following optional parts are also required.

Refrigerant branching kit.

Description

Model name

Refnet header

KHRP26M22H9
KHRP26M33H9
KHRP26M72H9

KHRP26M73HU9

Refnet joint

KHRP26M22T
KHRP26M33T

KHRP26M72TU9
KHRP26M73TU9

For the selection of the optimal branching kit, please refer to  

7.4. Selection of refrigerant branch kits on page 10.

Outdoor unit multi connection piping kit.

Number of outdoor units connected

2

3

BHFP22P100U

BHFP22P151U

In order to control the cooling or heating operation from a central 
location, the following option can be connected:

 

-  Cool/Heat selector: KRC19-26A

 

-

 With optional fixing box for the switch: KJB111A

 

- Centralized control devices (e.g., intelligent Touch Manager)

To instruct specific operation with an external input coming from a 
central control the external control adaptor (DTA104A61/62) can 

be used. Instructions (group or individual) can be instructed for low 
noise operation and power consumption limitation operation.

For VRV IV heat pump system it is also possible to make several 

commissioning field settings through a personal computer inter

-

face. For this option EKPCCAB* is required which is a dedicated 

cable to communicate with the outdoor unit. The software for the 
user interface program can be obtained from your local Daikin 

sales office.

 INFORMATION

Refer to the technical engineering data for the latest option names. 

Summary of Contents for RXYQ120TTJU


















































Reviews: