background image

24

3P362438-1B English

For VRV IV heat pump system it is alternatively possible to make 

several commissioning field settings through a personal computer 
interface (for this, option EKPCCAB* is required). The installer can 
prepare the configuration (off-site) on PC and afterwards upload the 
configuration to the system. How to connect the cable is described in 

 

13.3. Connecting the PC configurator to the outdoor unit on 
page 25.

The contents of the actual settings is discussed and explained in 15.2. 
Monitoring function and field settings on page 32.

13 .1 .  Accessing the push buttons on the logic board

It is not required to open the complete control box to access the push 

buttons on the logic board and read out the 7 segment display (s).

To access you can remove the front inspection door of the front panel 

(see figure). Now you can open the inspection door of the control box 
front panel (see figure). You can see 3 push buttons and 3 seven-

segment displays and DIP switches.

1

2

1  Front panel
2  Main printed circuit board with 3 seven-segment display 

and 3 push buttons

Operate the switches and push buttons with an insulated stick (such 
as a closed ballpoint pen) to avoid touching of live parts.

Location of the segment displays, buttons and DIP switches:

BS1 BS2

DS1 DS2

BS3

X27A

1

2

BS1 MODE

for changing the set mode

BS2 SET 

for field setting

BS3 

RETURN for field setting

DS1, DS2 

DIP switches

7 segment displays (3

×

)

Push buttons

Segment display indications: 
 

      

 Off

  Blinking
  On

13 .2 .  Operating the push buttons and DIP switches on 

the logic board

13 .2 .1 .  Operating the push buttons

By operating the push buttons it is possible to:

• 

Perform special actions (automatic refrigerant charge, test run, etc).

•  Perform field settings (demand operation, low noise, etc).

Below procedure explains how to operate the push buttons to reach 

the required mode in the menu, select the correct setting and modify 
the value of the setting. This procedure can be used any time special 

settings and regular field setting are discussed in this manual (see 
15.2. Monitoring function and field settings on page 32).

Setting definition: [A-B]=C; A=mode; B=setting; C=setting value. A, B 
and C are numerical values for field settings. Parameter C has to be 
defined. It can be a chosen from a set (0, 1, 2, 3, 4, 5, …) or regarded 

as an ON/OFF (1 or 0) depending on the contents. This is informed 

when the field setting is explained (see 15.2. Monitoring function and 
field settings on page 32).

 INFORMATION

During special operation (e.g., automatic refrigerant charging, test 
run, etc.) or when an malfunction happened, information will contain 
letters and numerical values.

Functions of the push button switches which are located on the 

outdoor printed circuit board (A1P)

Turn on the power supply of the outdoor unit and all indoor units. 
When the communication between indoor units and outdoor unit (s) is 
established and normal, the segment indication state will be as follows 
(default situation when shipped from factory):

When turning on the power supply, the display flashes on and off. First 
checks of the power supply are executed (1 – 2 min).

When no trouble occurs: lighted as indicated (8 – 10 min).

Ready for operation: blank display indication as indicated.

When above situation cannot be confirmed after 12 min, the malfunc

-

tion code can be checked on the indoor unit user interface and the 
outdoor unit segment display. Solve the malfunction code accordingly. 

The communication wiring should be checked at first.

 INFORMATION

Be sure to turn the power on at least 6 hours before operation in order 
to have power running to the crank case heater.

Accessing modes

BS1 is used to change the mode you want to access.

• 

Access mode 1
Push BS1 one time. Segment indication changes to:

Summary of Contents for RXYQ120TTJU


















































Reviews: