background image

5

English

Installation Space Requirements

•  Position the unit on a horizontal surface. Any tilt in the unit should be 3° or less to the horizontal.
• 

Where a wall or other obstacle is in the path of the outdoor unit’s intake or exhaust airflow, follow the installation space requirements 

below.

• 

For any of the below installation patterns, the wall height on the outlet side should be 47-1/4 inch (1200mm) or less.

• 

Secure as much installation space around the unit as the location allows, as more space will result in more efficient operation.

Wall facing one side

Walls facing three sides

Walls facing two sides

More than 

3-15/16 (100)

More than 

13-3/4 (350)

More than 

1-15/16 (50)

Side view

Top view

Top view

unit: inch (mm)

More than 3-15/16 (100)

More than 13-3/4 (350)

47-1/4
(1200)

or less

More than

3-15/16 (100)

More than 

13-3/4 

(350)

More than 

1-15/16 (50)

More 
than 

3-15/16 
(100)

More than 

1-15/16 (50)

More than

13-3/4 (350)

When installed as in the figure on the left, it is recommended to either 

change the orientation of the outdoor unit outlet side or use the air direction 

adjustment grille (sold separately).

Outdoor Unit Installation

1. 

Installing the outdoor unit

•  When installing the outdoor unit, refer to “

Precautions for Selecting a Location

” on page 3 and the “

Outdoor Unit 

Installation Diagram

” on page 4.

•  If drain work is necessary, follow the procedures below.

2. 

Drain work

CAUTION

• 

In cold areas, do not use a drain socket, drain caps (1, 2) and a drain hose with the outdoor unit. (Drain water may freeze, 
impairing heating performance.)

• 

If the drain port is covered by a mounting base or floor 
surface, place additional foot bases of at least 1-1/4 
inch (30mm) in height under the outdoor unit’s feet.

1) 

Attach 

B

 drain cap (1) and 

C

 drain cap (2).

2) 

Attach 

A

 drain socket.

•  When attaching 

A

 drain socket to the bottom 

frame, make sure to connect the drain hose to the 

drain socket first.

A  Drain socket

A  Drain socket

Bottom frame

Hose (available commercially, 

inner dia. 5/8” (16mm))

Bottom frame

Drain cap

Pinch the bottom 
frame in.

C  Drain cap (2)

C  Drain cap (2)

B

 Drain cap (1)

Air outlet side

01_EN_3P686856-1.indd   5

2022/04/20   9:15:05

Summary of Contents for RXM09WVJU9















Reviews: