background image

4 About the system

Installation and operation manual

8

REYQ8~20+REMQ5U7Y1B

VRV IV+ heat recovery

4P546222-1B – 2020.10

WARNING

Never touch the air outlet or the
horizontal blades while the swing flap
is in operation. Fingers may become
caught or the unit may break down.

CAUTION

Do NOT insert fingers, rods or other
objects into the air inlet or outlet. Do
NOT remove the fan guard. When the
fan is rotating at high speed, it will
cause injury.

CAUTION: Pay attention to the fan!

It is dangerous to inspect the unit while
the fan is running.

Be sure to turn off the main switch
before executing any maintenance
task.

CAUTION

After a long use, check the unit stand
and fitting for damage. If damaged, the
unit may fall and result in injury.

WARNING

NEVER replace a fuse with a fuse of a
wrong ampere ratings or other wires
when a fuse blows out. Use of wire or
copper wire may cause the unit to
break down or cause a fire.

WARNING

▪ Do NOT modify, disassemble,

remove, reinstall or repair the unit
yourself as incorrect dismantling or
installation may cause an electric
shock or fire. Contact your dealer.

▪ In case of accidental refrigerant

leaks, make sure there are no naked
flames. The refrigerant itself is
entirely safe, non-toxic and non-
combustible, but it will generate toxic
gas when it accidentally leaks into a
room where combustible air from fan
heaters, gas cookers, etc. is present.
Always have qualified service
personnel confirm that the point of
leakage has been repaired or
corrected before resuming operation.

WARNING

Stop operation and shut off the
power if anything unusual occurs
(burning smells etc.).

Leaving the unit running under such
circumstances may cause breakage,
electric shock or fire. Contact your
dealer.

WARNING

The refrigerant in the system is safe
and normally does not leak. If the
refrigerant leaks in the room, contact
with a fire of a burner, a heater or a
cooker may result in a harmful gas.

Turn off any combustible heating
devices, ventilate the room and contact
the dealer where you purchased the
unit.

Do not use the system until a service
person confirms that the portion where
the refrigerant leaks is repaired.

CAUTION

NEVER expose little children, plants or
animals directly to the airflow.

CAUTION

Do NOT touch the heat exchanger fins.
These fins are sharp and could result
in cutting injuries.

4

About the system

The indoor unit part of VRV IV heat recovery system can be used for
heating/cooling  applications.  The  type  of  indoor  unit  which  can  be
used depends on the outdoor units series.

NOTICE

For future modifications or expansions of your system:

A  full  overview  of  allowable  combinations  (for  future
system  extensions)  is  available  in  technical  engineering
data  and  should  be  consulted.  Contact  your  installer  to
receive more information and professional advice.

4.1

System layout

Your  VRV  IV  heat  recovery  series  outdoor  unit  can  be  one  of
following models:

Model

Description

REYQ8~20

Heat recovery model for single or multi-use

REMQ5

Heat recovery model for multi-use only

Summary of Contents for REYQ8U7Y1B





















































Reviews: