background image

19 Troubleshooting

Installation and operation manual

42

REYQ8~20+REMQ5U7Y1B

VRV IV+ heat recovery

4P546222-1B – 2020.10

Main code

Sub code

Cause

Solution

Master

Slave 1

Slave 2

Discharge temperature sensor
malfunction (R21T): open circuit – main
PCB (X19A)

Check connection on PCB or actuator.

Discharge temperature sensor
malfunction (R21T): short circuit - main
PCB (X19A)

Check connection on PCB or actuator.

Discharge temperature sensor
malfunction (R22T): open circuit - main
PCB (X19A)

Check connection on PCB or actuator.

Discharge temperature sensor
malfunction (R22T): short circuit - main
PCB (X19A)

Check connection on PCB or actuator.

Compressor casing temperature sensor
malfunction (R15T): open circuit - main
PCB (X19A)

Check connection on PCB or actuator.

Compressor casing temperature sensor
malfunction (R15T): short circuit - main
PCB (X19A)

Check connection on PCB or actuator.

Suction compressor temperature sensor
(R12T) – sub PCB (X15A)

Check connection on PCB or actuator.

Suction temperature sensor (R10T) –
main PCB (X29A)

Check connection on PCB or actuator.

Heat exchanger deicer temperature
sensor (R11T) – sub PCB (X15A)

Check connection on PCB or actuator

Upper heat exchanger – gas -
temperature sensor (R8T) – main PCB
(X29A)

Check connection on PCB or actuator.

Lower heat exchanger – gas -
temperature sensor (R9T) main PCB
(X29A)

Check connection on PCB or actuator.

Liquid main - temperature sensor (R3T)
– main PCB (X30A)

Check connection on PCB or actuator.

Subcool heat exchanger – liquid -
temperature sensor (R7T) - main PCB
(X30A)

Check connection on PCB or actuator.

Upper heat exchanger – liquid -
temperature sensor (R4T ) - main PCB
(X30A)

Check connection on PCB or actuator.

Lower heat exchanger – liquid -
temperature sensor (R5T ) - main PCB
(X30A)

Check connection on PCB or actuator.

Auto charge temperature sensor (R14T )
– sub PCB (X15A)

Check connection on PCB or actuator.

Subcool heat exchanger – gas -
temperature sensor (R6T) – main PCB
(X30A)

Check connection on PCB or actuator.

Receiver gas temperature sensor
(R13T) – sub PCB (X17A)

Check connection on PCB or actuator.

High pressure sensor malfunction
(S1NPH): open circuit - main PCB
(X32A)

Check connection on PCB or actuator.

High pressure sensor malfunction
(S1NPH): short circuit - main PCB
(X32A)

Check connection on PCB or actuator.

Low pressure sensor malfunction
(S1NPL): open circuit - main PCB
(X31A)

Check connection on PCB or actuator.

Low pressure sensor malfunction
(S1NPL): short circuit - main PCB
(X31A)

Check connection on PCB or actuator.

Summary of Contents for REYQ8U7Y1B





















































Reviews: