background image

17 Commissioning

Installation and operation manual

38

REYQ8~20+REMQ5U7Y1B

VRV IV+ heat recovery

4P546222-1B – 2020.10

▪ For  details  concerning  the  calculation  of  additional  refrigerant

charge  amount,  see 

"To  determine  the  additional  refrigerant

amount"

 [

4

 25].

▪ For  guidance  concerning  the  input  of  the  additional  refrigerant

charge  amount  and  leak  detection  function  see 

"16.2  Using  the

leak detection function"

 [

4

 38].

[2‑20]

Manual additional refrigerant charge.

[2‑20]

Description

0 (default)

Deactivated.

1

Activated.

To stop the manual additional refrigerant
charge operation (when the required additional
refrigerant amount is charged), push BS3. If
this function was not aborted by pushing BS3,
the unit will stop its operation after 30 minutes.
If 30 minutes was not sufficient to add the
needed refrigerant amount, the function can be
reactivated by changing the field setting again.

[2‑35]

Height difference setting.

[2‑35]

Description

0

In case the outdoor unit is installed in the
lowest position (indoor units are installed on a
higher position than outdoor units) and the
height difference between the highest indoor
unit and the outdoor unit exceeds 40 m, the
setting [2‑35] should be changed to 0.

1 (default)

[2‑45]

Technical cooling.

[2‑45]

Description

0 (default)

No technical cooling available

1

Technical cooling available

For more information about this setting, refer to the service manual.

[2‑47]

T

target temperature during heat recovery operation.

[2‑47]

T

e

 target (°C)

0 (default)

Auto

2

6

3

7

4

8

5

9

6

10

7

11

[2‑49]

Height difference setting.

[2‑49]

Description

0 (default)

1

In case the outdoor unit is installed in the
highest position (indoor units are installed on a
lower position than outdoor units) and the
height difference between the lowest indoor
unit and the outdoor unit exceeds 50 m, the
setting [2‑49] has to be changed to 1.

16.1.9

To connect the PC configurator to the
outdoor unit

X27A

a

b

c

2

3

4

5

H J

ST

X27A

A1P

a

PC

b

Cable (EKPCCAB*)

c

Outdoor unit main PCB

16.2

Using the leak detection function

16.2.1

About automatic leak detection

The  (automatic)  leak  detection  function  is  not  by  default  activated
and can only start working when the additional refrigerant charge is
inputted into the system's logic (see [2‑14]).

The  leak  detection  operation  can  be  automated.  By  changing
parameter [2‑85] to chosen value, the interval time or the time till the
next  automatic  leak  detection  operation  can  be  chosen.  The
parameter  [2‑86]  defines  whether  the  leak  detection  operation  is
executed one time (within [2‑85] days) or intermittent, respecting an
interval of [2‑85] days.

Availability of the leak detection function feature requires input of the
additional  refrigerant  charge  amount  immediately  after  finishing  the
charging.  The  input  must  be  executed  before  performing  the  test
operation.

NOTICE

If  a  wrong  value  is  input  for  the  additional  charged
refrigerant  weight,  the  accuracy  of  the  leak  detection
function will decrease.

INFORMATION

▪ The  weighed  and  already  recorded  amount  of

additional  refrigerant  charge  (not  the  total  amount  of
refrigerant present in the system) must be entered.

▪ The  leak  detection  function  is  not  available  when

Hydrobox units are connected to the system.

▪ When  the  height  difference  between  indoor  units  is

≥50/40 m, the leak detection function can not be used.

17

Commissioning

NOTICE

General 

commissioning 

checklist.

 

Next 

to 

the

commissioning  instructions  in  this  chapter,  a  general
commissioning  checklist  is  also  available  on  the  Daikin
Business Portal (authentication required).

The  general  commissioning  checklist  is  complementary  to
the  instructions  in  this  chapter  and  can  be  used  as  a
guideline and reporting template during the commissioning
and hand-over to the user.

Summary of Contents for REYQ8U7Y1B





















































Reviews: