Daikin FXKQ25MVE, Installation Manual

Page: 4 / 14

2 English
2. BEFORE INSTALLATION
• When moving the unit while removing it from the carton
box, be sure to lift it by holding on to the four lifting lugs
without exerting any pressure on other parts, especially,
the refrigerant piping, drain piping, and other resin parts.
• Be sure to check the type of R410A refrigerant to be used
before installing the unit.(Using an incorrect refrigerant will
prevent normal operation of the unit.)
• The accessories needed for installation must be retained in
your custody until the installation work is completed. Do not
discard them!
• Decide upon a line of transport.
• Leave the unit inside its packaging while moving, until reach-
ing the installation site. Where unpacking is unavoidable, use
a sling of soft material or protective plates together with a
rope when lifting, to avoid damage or scratches to the unit.
• When selecting installation site, refer to the paper pattern.
• For the installation of an outdoor unit, refer to the installation
manual attached to the outdoor unit.
• Do not install or operate the unit in rooms mentioned below.
• Laden with mineral oil, or filled with oil vapor or spray
like in kitchens. (Plastic parts may deteriorate which
could eventually cause the unit to fall out of place, or
could lead to leaks.)
• Where corrosive gas like sulfurous gas exists. (Cop-
per tubing and brazed spots may corrode which could
eventually lead to refrigerant leaks.)
• Where exposed to combustible gases and where vol-
atile flammable gas like thinner or gasoline is used.
(Gas in the vicinity of the unit could ignite.)
• Where machines can generate electromagnetic
waves. (Control system may malfunction.)
• Where the air contains high levels of salt such as that
near the ocean and where voltage fluctuates greatly
such as that in factories. Also in vehicles or vessels.
• This unit, both indoor and outdoor, is suitable for installation
in a commercial and light industrial environment.
If installed as a household appliance it could cause electro-
magnetic interference.
2-1 PRECAUTIONS
• Be sure to read this manual before installing the indoor unit.
• Entrust installation to the place of purchase or a qualified ser-
viceman. Improper installation could lead to leaks and, in
worse cases, electric shock of fire.
• Use only parts provided with the unit or parts satisfying
required specifications. Unspecified parts could cause the
unit to fall out of place, or could lead to leaks and, in worse
cases, electric shock or fire.
2-2 ACCESSORIES
Check the following accessories are included with your unit.
• Screws for fixing panels are attached to decoration panel.
2-3 OPTIONAL ACCESSORIES
• The optional decoration panel and remote controller are
required for this indoor unit. (Refer to Table 1, 2)
Table 1
• These are two types of remote controllers: wired and wire-
less. Select a remote controller from the Table 2 according to
customer request and install in an appropriate place.
Table 2
NOTE
• If you wish to use a remote controller that is not listed in
Table 2 on page 2, select a suitable remote controller after
consulting catalogs and technical materials.
Name
Metal
clamp
Paper pattern for
installation
Drain hose
Quantity 1pc. 1 pc. 1 pc.
Shape
Corrugated cardboard
Name
Insulation for
fitting
Sealing pad
Insulation for
hanger
bracket
Quantity 1 each. 1 each. 4 pcs.
Shape
For gas pipe
For liquid pipe
Large
Small
Name
Washer for
hanging
bracket
Clamp
Positioning jig for
installation
Quantity 8 pcs. 8 pcs. 2 each.
Shape
Name Air outlet blocking pad
(Other)
•
Operation manual
•
Installation manual
Quantity 1 pc.
Shape
Model
Min. height
above ceiling
Decoration panel
White
FXKQ25 · 32 ·
40MVE
220 mm or more
BYK45FJW1
FXKQ63MVE BYK71FJW1
Remote controller
Wired type
Wireless type
Heat pump type
Cooling only type
4 screws
01_EN_3P086156-8F.fm Page 2 Wednesday, March 19, 2003 6:55 PM