background image

4

English

[ PRECAUTION ]

If installing the wireless kit in a room with electronic fluores-
cent lighting (inverter or rapid start type), the remote con-
troller’s transmission distance may be shortened. Indoor 
units should be installed as far away from fluorescent light-
ing as possible.

(2) Ceiling height 

These units can be installed with ceilings up to 3 m in 
height.
Install this unit where the height of bottom panel is more 
than 2.5 m so that the user cannot easily touch.

(3) Use suspension bolts for installation. Check whether 

the ceiling is strong enough to support the weight of 
the unit or not. If there is a risk, reinforce the ceiling 
before installing the unit.

(Installation pitch is marked on the paper pattern for instal-
lation. Refer to it to check for points requiring reinforcing.)

4.

PREPARATIONS BEFORE INSTALLATION

(1) Relation of ceiling opening to units and suspension 

bolt position

(2) Make the ceiling opening needed for installation, where 

applicable.

• Refer to the paper pattern for installation for ceiling open-

ing dimension.

• Create the ceiling opening required for installation. From 

the side of the opening to the casing outlet, implement 
the refrigerant and drain piping and wiring for remote con-
troller (unnecessary for wireless type) and indoor-out-
door unit casing outlet. Refer to each PIPING or WIRING 
section.

• After making an opening in the ceiling, it may be neces-

sary to reinforce ceiling beams to keep the ceiling level 
and to prevent it from vibrating. Consult the builder for 
details.

(3) Install the suspension bolts. (Use either a W3/8 or M10 

size bolt.) 

Use a hole-in-anchor for existing ceilings, and a sunken 
insert, sunken anchor or other part to be procured in the 
field for new ceilings to reinforce the ceiling to bearing the 
weight of the unit. Adjust clearance from the ceiling before 
proceeding further.

5.

INDOOR UNIT INSTALLATION



Installing optional accessories (except for the decoration 

panel) before installing the indoor unit is easier. However, 
for existing ceilings, install branch duct before installing 
the unit.



As for the parts to be used for installation work, be sure to use 
the provided accessories and specified parts designated by our 
company.

(1) Install the indoor unit temporarily.

• Attach the hanger bracket to the suspension bolt. Be sure 

to fix it securely by using a nut and washer from the upper 
and lower sides of the hanger bracket. The washer fixing 
plate will prevent the washer from falling.

350

1500

1500

1000

[ Space required for installation ]

100

100

(length:mm)

2500 or more

For installation

in high places

       

Decoration 
panel

Ceiling opening

Indoor unit

Suspension bolt 
(× 4)

D (Panel outside dimensions)

A (Ceiling opening)

B (Suspension pitch)

C (Unit outside dimensions)

20

20

20

20

680 (Panel outside dimensions)

640 (Ceiling opening)

600 (Unit outside dimensions)

520 (Suspension pitch)

(length:mm)

Model

A (mm)

B (mm)

C (mm)

D (mm)

FXCQ20 · 25 · 32MVE

990

820

775

1030

FXCQ40 · 50MVE

1205

1035

990

1245

FXCQ63MVE

1390

1220

1175

1430

FXCQ80 · 125MVE

1880

1710

1665

1920

160

[ Relative positioning of ceiling and unit ]

Hanger

Ceiling surface

(length:mm)

100mm

[ Installation example ]

Ceiling slab

Anchor

Long nut or turn-buckle

Suspension bolt

False ceiling

Note: All the above parts are 

fi

eld supplied.

01_EN_3P258319-5K.fm  Page 4  Thursday, October 15, 2015  11:03 AM

Summary of Contents for FXCQ125MVE















Reviews: