background image

English

2

Accessories

 

 – 

,  

Choosing an Installation Site

• Before choosing the installation site, obtain user approval.

1.

Indoor unit.

• The indoor unit should be sited in a place where: 

1) the restrictions on installation specified in the indoor unit installation drawings are met,
2) both air intake and exhaust have clear paths met,
3) the unit is not in the path of direct sunlight,
4) the unit is away from the source of heat or steam,
5) there is no source of machine oil vapour (this may shorten indoor unit life),
6) cool (warm) air is circulated throughout the room,
7) the unit is away from electronic ignition type fluorescent lamps (inverter or rapid start type) as they may shorten the 

remote control range,

8) the unit is at least 1 metre away from any television or radio set (unit may cause interference with the picture or sound).

2.

Wireless remote controller.

1) Turn on all the fluorescent lamps in the room, if any, and find the site where remote control signals are properly received 

by the indoor unit (within 7 metres).

 

Mounting plate

1

 Remote controller holder

1

 Operation manual

1

 Titanium Apatite 

Photocatalytic 
Air-Purifying Filter 

2

 AAA dry-cell batteries

2

 

Installation manual

1

 Wireless remote controller

1

 Indoor unit fixing screws 

(M4 × 12L)

2

Indoor unit

A

L

A

E

K

B

G

L

D

H

01_EN_3P142639-1.fm  Page 2  Monday, October 11, 2004  3:59 PM

Summary of Contents for FTXS20DVMW
















Reviews: