background image

English

8

3-2. Left-side, left-back, or left bottom piping.

1) Attach the drain hose to the underside of the refrigerant pipes 

with adhesive vinyl tape.

2) Be sure to connect the drain hose to the drain port in place of a 

drain plug.

3) Shape the refrigerant pipe along 

the pipe path marking on the 
mounting plate.

4) Pass drain hose and refrigerant 

pipes through the wall hole, then 
set the indoor unit on mounting 

plate hooks, using the 

 mark-

ings at the top of indoor unit as a 
guide.

5) Pull in the interconnecting wires.
6) Connect the inter-unit piping.

7) Wrap the refrigerant pipes and 

drain hose together with insulation tape as right figure, in case of setting 
the drain hose through the back of the indoor unit.

8) While exercising care so that the interconnecting wires do not catch indoor 

unit, press the bottom edge of indoor unit with both hands until it is firmly 
caught by the mounting plate hooks.  Secure indoor unit to the mounting 
plate with screws (M4 × 12L).

3-3. Wall embedded piping.

Follow the instructions given under

1) Insert the drain hose to this depth so it won’t be pulled out of the drain 

pipe.

Left-side, left-back, or left bottom piping

Remove pipe port cover here for left-bottom piping.

Remove pipe 
port cover 
here for left-
side piping.

Left-bottom piping

Left-side 
piping

Left-back 
piping

How to set drain plug.

No gap.

Do not apply lubricating 
oil (refrigerant machine 
oil) when inserting.
Application of causes 
deterioration and drain 
leakage of the plug.

Insert a hexagon wrench (4 mm).

Wrap insulating tape around the bent portion 
of refrigerant pipe. 
Overlap at least half the width of the tape 
with each turn.

Drain 
hose

Caulk this hole 
with putty or 
caulking material.

Bind with plastic 
tape.

 A Mounting plate

Refrigerant
pipes

Drain hose

Bottom frame

H  M4 

×

 12L (2 point)

Mounting
plate

A

Inner wall

Vinyl chloride 
drain pipe 
(VP-30)

Drain hose

50 mm 
or more

Insert drain hose 
to this depth so 
it won’t be pulled 
out of drain pipe.

Outer wall

01_EN_3P142639-1.fm  Page 8  Monday, October 11, 2004  3:59 PM

Summary of Contents for FTXS20DVMW
















Reviews: