background image

3

English

Installation Tips

1.

Removing and installing front panel.

• Removal  method

Hook fingers on the panel protrusions on the left and right of the main 
body, and open until the panel stops. Slide the front panel sideways to dis-
engage the rotating shaft. Then pull the front panel toward you to remove 
it.

• Installation method

Align the tabs of the front panel with the grooves, and push all the way in. Then 
close slowly. Push the center of the lower surface of the panel firmly to engage the 
tabs.

2.

Removing and installing front grille.

• Removal  method

1) Remove front panel to remove the air filter.
2) Remove the front grille.
3) In front of the 

!!!

 mark of the front grille, there are 3 upper hooks. Lightly pull the 

front grille toward you with one hand, and push down on the hooks with the fingers of 
your other hand.

When there is no work space because the unit is close to ceiling

Caution

Be sure to wear protection gloves.

Place both hands under the center of the front grille, and while pushing up, pull it toward you.

• Installation method

1) Install the front grille and firmly engage the upper hooks (3 locations).
2) Install 2screws of the front grille.
3) Install the air filter and then mount the front panel.

Push the 
rotating shaft 
of the front 
panel into the 
groove.

¡¡¡

 mark area 

(3 locations)

Upper hook

Lightly pull the front 
grille toward you with 
one hand, and push 
down on the hooks with 
the fingers of your other 
hand. (3 locations)

Push
down.

Upper hook

Upper hook

1) Push up.

2) Pull toward you.

01_EN_3P142639-1.fm  Page 3  Monday, October 11, 2004  3:59 PM

Summary of Contents for FTXS20DVMW
















Reviews: