background image

English

18

PRECAUTIONS

Refer to the diagnoses below if the unit does not operate properly.

After completing the test run, press the INSPECTION/TEST OPERATION button once to put the 
unit in inspection mode, and make sure the Malfunction code is “00” (=normal).
If the code reads anything other than “00”, refer to the malfunction diagnoses below.

NOTE

If a malfunction is preventing operation, refer to the malfunction diagnoses below.

2. Cautions for servicing

With the power on. Troubles can be monitored on the remote controller.

If the air conditioner does not operate normally after installing the air conditioner.
a malfunction shown in the table below may happened.

After turning on the power, the maximum is 90 seconds, although it will only display “88”. This is not
a problem, and it will be set for 90 seconds.

!

Trouble shooting with the display on the liquid crystal display remote controller.
With the wired remote controller. (NOTE 1) 
When the operation stops due to trouble, operation lamp flashed, and “ 

 ” and the Malfunction 

code are indicated on the liquid crystal display. In such a case, diagnose the fault contents by refer-
ing to the table on the Malfunction code list it case of group control, the unit No. is displayed so that 
the indoor unit no with the trouble can be recognized. (NOTE 2)

NOTE

1.

In case wired remote controller. Press the INSPECTION /TEST OPERATION button on remote con-
troller, “ 

 ” starts flashing and changes the inspection mode.

2.

Keep down the ON/OFF button for 5 seconds or longer in the inspection mode and the above trouble 
history disappears, after the Malfunction code goes on and off twice, followed by the code “00”(nor-
mal). The display changes from the inspection mode to the normal mode.

3. Malfunction code

For places where the Malfunction code is left blank, the “

” indication is not displayed. Though the 

system continues operating, be sure to inspect the system and make repairs as necessary.

Depending on the type of indoor or outdoor unit, the Malfunction code may or may not be displayed.

Remote control display

Malfunction

No display

Power supply trouble or Open phase connection

Wrong wiring between indoor and outdoor unit

Indoor PC board faulty

Wrong remote control connection wiring

Remote control faulty

Fuse faulty

88

Indoor PC board faulty

Wrong wiring between indoor and outdoor unit

88 flashing

Wrong wiring between indoor and outdoor unit

 Code

Malfunction/Remarks

A1

Indoor unit’s PC board faulty

A3

Drain water level abnormal

A6

Indoor fan motor overloaded, overcurrent or locked

A7

Swing flap motor locked
Only the air flow direction can not be controlled.

AF

Humidifier faulty

AH

Air cleaner faulty
Only the air cleaner does not function.

01_EN_3P156215-4C.fm  Page 18  Saturday, May 14, 2005  9:17 AM

Summary of Contents for FBQ60BV1
























Reviews: