background image

19

English

9-5 CONTROL BY 2 REMOTE CONTROLLERS 

(Controlling 1 indoor unit by 2 remote controllers)

When using 2 remote controllers, one must be set to “MAIN” and the other to “SUB”.

MAIN/SUB CHANGEOVER

1.

Insert a wedge-head screwdriver into the recess between the upper and lower parts of remote con-
troller and, working from the 2 positions, remove carefully the upper part.

 (Refer to Fig. 22)

(The remote controller PC board is attached to the upper part of the remote controller.)

2.

Turn the MAIN/SUB changeover switch on one of the two remote controller PC board to “S”.
(Leave the switch of the other remote controller set to “M”.) 

(Refer to Fig. 23)

9-6

COMPUTERISED CONTROL (FORCED OFF AND ON/OFF OPERATION) FOR FAQ MODEL

(1) Wire specifications and how to perform wiring 

Connect input from outside to terminals T1 and T2 of the terminal block for remote controller.

(2) Actuation

The following table explains FORCED OFF and ON/OFF OPERATIONS in response to Input A. 

(3) How to select FORCED OFF and ON/OFF OPERATION 

Turn the power on and then use the remote controller to select operation.

Wire specification

Sheathed vinyl cord or cable (2 wire)

Gauge

0.75 - 1.25 mm

2

Length

Max. 100 m

External terminal

Contact that can ensure the minimum applicable load of 15 V DC, 10 mA.

FORCED OFF

ON/OFF OPERATION

Input “ON” stops operation (impossible by remote controllers.)

Input OFF 

→ 

ON turns ON unit.

Input OFF enables control by remote controller.

Input ON 

→ 

OFF turns OFF unit.

Lower part of 
remote controller

Upper part of 
remote controller

Fig. 22

Insert the screwdriver here and gently 
work off the upper part of remote controller.

S

M

S

S

M

Factory setting

Only one remote controller 
needs to be changed 
if factory settings have 
remained untouched.

Remote 
controller 
PC board

Fig

.

23

F2

T1

T2

FORCED
OFF

Input A

01_EN_3P083811-3T.fm  Page 19  Friday, September 3, 2004  10:17 AM

Summary of Contents for FAY71LVE































Reviews: