background image

3

English

Do not install or operate the unit in rooms mentioned below.

Laden with mineral oil, or filled with oil vapor or spray like in kitchens. (Plastic parts may deterio-
rate.)

Where corrosive gas like sulfurous gas exists. (Copper tubing and brazed spots may corrode.)

Where volatile flammable gas like thinner or gasoline is used.

Where machines can generate electromagnetic waves. (Control system may malfunction.)

Where the air contains high levels of salt such as that near the ocean and where voltage fluctuates 
greatly such as that in factories. Also in vehicles or vessels.

2. ACCESSORIES

Check the following accessories are included with the unit.

Where to locate accessories

3. OPTIONAL ACCESSORIES

The remote controller are required for this indoor unit.
(However, the remote controller is not required for the slave unit of a simultaneous operation system.)

These are two types of remote controllers: wired and wireless.  Select a remote controller from 
Table 1 according to customer request and install in an appropriate place.
(For installation, follow the Installation manual included with the remote controllers.)

Table 1

NOTE

If the customer wishes to use a remote controller that is not listed above, select a suitable remote 
controller after consulting catalogs and technical materials.

Name

1) Installation 

panel

Insulation for fitting

(for refrigerant pipe)

4) Insulation 

tape

5) Paper pattern 

for installation

(Other)

• Operation 

manual

• Installation 

manual

Quantity

1 1each

2

1

Shape

2) For liquid pipe

 3) For gas pipe

Remote controller

Model

FAY-FJV1 type

Wired type

BRC1C517, BRC1B517

Wireless type

Heat pump type

BRC7C54W

Cooling only type

BRC7C59W

FAYP-BV1 type

Wired type

BRC1C517

Wireless type

Heat pump type

BRC7C510W, BRC7CA510W

Cooling only type

BRC7C511W, BRC7CA511W

FAQ type

Wired type

BRC1D527, BRC1D528, BRC1C61

Wireless type

Heat pump type

BRC7C510W, BRC7CA510W

Cooling only type

BRC7C511W, BRC7CA511W

6) Screw×12

Indoor unit and installation panel

Accesories (Attached to the rear side of indoor unit.)

Box

01_EN_3P184443-2.fm  Page 3  Monday, July 3, 2006  3:14 PM

Summary of Contents for FAY71FJV1


























Reviews: