background image

Installing the unit 

 

EKLN140A1 

 

Installation manual 

Low sound enclosure 

9

 

4P650154-1 

 2021.03 

 

 

4. 

Press the side panels tight and lock them with the key provided 
(accessory R). 

The low sound enclosure has been fitted. 

4.7  Configuration 

After  installing  the  unit  ALWAYS  deactivate  the  high  ESP  function. 
This in order to avoid increased fan velocity and related increase in 
outdoor sound emission. 

Unit 

Setting 

Set to value …

 

RZAG71/100/125/140N7* 

2-79 

RZA200/250D7Y1B 

2-79 

RXYSA4/5/6A7* 

2-18 

 

 

INFORMATION 

 

For  further  information  on  the  field  settings,  see  the 
installer reference guide or the service manual for the unit. 

 

4.8  Maintenance 

The  low  sound  enclosure  is  free  of  maintenance  under  normal 
conditions. 

Clean  the  outside  with  water  and  a  mild  cleaning  agent  at  regular 
intervals to keep the housing in optimal condition. 

So as not to impair the return from the heat pump, there must be no 
blockages  in  the  ventilation  openings.  Always  remove  dirt  (such  as 
leaves) and snow. 

 

INFORMATION 

 

For  information  on  maintaining  the  heat  pump,  see  the 
maintenance manual for the respective heat pump. 

 

Summary of Contents for EKLN140A1













Reviews: