manualshive.com logo in svg

Daiichi Electronics SQLC-110L, Instruction Manual, Page: 70 / 74

Share
Download
Daiichi Electronics SQLC-110L Instruction Manual Download Page 70

SQLC-220-086 

 

69

 
 

7. Maintenance and check 

7.1 Trouble shooting 

Symptoms 

Possible causes 

Remedial measures 

Indicator does not 
display. 

The power supply is not supplied.  
(Not connected. or voltage is low)  

Check the auxiliary supply. 
Again, a power supply is supplied.  

Measurement display ON/OFF setting is set to OFF. 

Setting check. 

Trouble of device. 

Replace the device. 

Measuring value error 
is noticeable 

Range is not set correctly. 

Please set again.  

Out of range in rated frequency (45 to 65Hz). 

Cannot be used.  

Cycle control, SCR phase angle control, PWM, or  
other inverter output is measured. 

Cannot be used.  

Analog output is not 
outputted.  

Analog output is set to OFF or measurement factor  
is set to OFF. 

Please check setting 

Pulse output is not 
outputted.  

Pulse output is set to OFF or measurement factor is  
set to OFF. 

Please check setting 

Alarm output does not 
return.  

The return method is a "manual reset".  

Please check setting 

 
 

7.2 Test 

In case this product is tested, a special setting or operation is not needed fundamentally.   
However, the following test should operate it along with each process.  

 

(1) Alarm output test  

Even if this product does not have input, it can perform ON/OFF test of an alarm output (relay contact output).  
Operation is performed by alarm 1 test and alarm 2 test in the setting mode 1. 
Please refer to "5.3.1 Setting mode 1 (2) alarm output setup" about the details of operation.  
 
In addition, an alarm return constitutes action corresponding to a return method setting (automatic reset /  
manual reset) of each alarm output. 
 
< Operating process > 

・Alarm 1 test (Setting № 124) 
                          (111)          (121)                             (124) 

Press  SET  for 3 seconds → Press  MODE  → Press  RESET/SHIFT  for 3 times → While pushing  SET , the  

alarm 1 output is ON.  

 
・Alarm 2 test (Setting № 128) 
                          (111)          (121)                             (128) 
  Press  SET  for 3 seconds → Press  MODE  → Press  RESET/SHIFT  for 7 times → While pushing  SET , the  

alarm 2 output is ON.  

 

(2) Harmonic time interval test  

Please test by the following operation about the time interval of a harmonic.  An error becomes large, in case 
it tests without performing the following operation.  
Operation is performed with the average time interval in the setting mode 1.  
Please refer to "5.3.1 setting mode 1 (4) harmonic detection setting" for operation details. 

 
< Operating process > (Setting № 14A) 
                           (111)                      (141)                               (14A) 

 Press  SET  for 3 seconds → Press  MODE  for 3 times → Press  RESET/SHIFT  for 9 times  
 
          Please press  SET  simultaneously with a test start. 
 
Please press  DISPLAY  and return to a measurement screen.  

 

Summary of Contents for SQLC-110L











































































Reviews:

No comments