Dahua HCVR8204A-S3 User Manual Download

Page: 380 / 446

370

Parameter Function

Control
mode

You can select control mode from the dropdown list. There are two

options: Serial/HDCVI. For HDCVI series product, please select

HDCVI. The control signal is sent to the PTZ via the coaxial cable. For

the serial mode, the control signal is sent to the PTZ via the RS485

port.

Protocol

Please select protocol from the dropdown list.

Address

Set corresponding dome address. Default value is 1.

Please note

your setup here shall comply with your dome address; otherwise

you cannot control the speed dome.

Baud Rate Select the dome baud rate. Default setup is 9600.

Data Bit

Default setup is 8. Please set according to the speed dome dial switch
setup.

Stop bit

Default setup is 1. Please set according to the speed dome dial switch

setup.

Parity

Default setup is none. Please set according to the speed dome dial
switch setup.

Step 3 Click Save button after you complete setup.

Go back to the monitor interface to control PTZ camera .

5.7.5.6 POS

Connect the DVR with the POS, the DVR can receive the POS information and overlay

corresponding info on the video.

Note



For the local-end, this function supports one-window display and playback only. For

the Web, it supports multiple-window display and payback.



This function is for the cashier of the supermarket and etc. The DVR can get the

information from the POS and then overlay the txt information on the video.

Step 1 From main menu->Setting->System->POS.

Enter POS interface. See Figure 5-145.

Figure 5-145

Step 2 Click Add.

Summary of Contents for HCVR8204A-S3































































































































































































































































































































































































































































Search results

Summary of Contents for HCVR8204A-S3

Reviews:

Related manuals for HCVR8204A-S3

Brands by name

Popular brands

Dahua HCVR8204A-S3, User Manual

Search results

Summary of Contents for HCVR8204A-S3

Reviews:

Related manuals for HCVR8204A-S3

Brands by name

Popular brands