Dahua HCVR8204A-S3 User Manual Download

Page: 276 / 446

266

Please refer to chapter 5.5 Preview,, chapter 5.7 setup , chapter 5.8 search, chapter 5.9

Alarm, chapter 5.6 Face search and chapter 5.11 Logout for detailed information.

Figure 5-9

5.5.1.2

Real-time Monitor

Left click the channel name on the left pane of the main interface; you can see the

corresponding video in current window.

On the top left corner, you can view device IP, channel number, network monitor bit stream.

See Figure 5-10.

Figure 5-10

Please refer to the following sheet for detailed information.

Name

Function

1-4

Display

device

information

When there is video, it is to display “Device IP-Monitor
channel number-network bit stream-

decode mode”.

Otherwise, it shows as “No video”.

Smart track

Click it to view the smart track video.

Fisheye

Click it to set fisheye installation mode and display

mode.

Digital zoom

Click this button and then left drag the mouse in the

zone to zoom in. right click mouse system restores

original status.

Local record

When you click local record button, the system begins

recording and this button becomes highlighted. You

can go to system folder RecordDownload to view the

recorded file.

Summary of Contents for HCVR8204A-S3































































































































































































































































































































































































































































Search results

Summary of Contents for HCVR8204A-S3

Reviews:

Related manuals for HCVR8204A-S3

Brands by name

Popular brands

Dahua HCVR8204A-S3, User Manual

Search results

Summary of Contents for HCVR8204A-S3

Reviews:

Related manuals for HCVR8204A-S3

Brands by name

Popular brands