Daewoo EGSP-130E Technical & Service Manual Download Page 33 | Manualshive

Page: 33 / 55

background image

PCB

Theory of parts

-

>

Printed Circuit Board is the control center of dishwasher, which receive and
process signal from components, send order to components and deal with the
feedback information, etc.

Removing the control panel

The control panel can be removed from dishwasher door.
1. Remove the six screws securing the control panel to the door.
2. The control panel will drop down and be free of the door. But, the wiring will
still connected to the control panel.

S

S

08

1
2

1
2

on

Off

Access PCB

3. Disconnect the connector form PCB.
4. Remove the two screws shown above securing the PCB to control panel.
5. Remove the PCB.
6. Reverse the above procedure to install.

PCB

32

«
...
31
32
33
34
35
...
»

Summary of Contents for EGSP-130E
























































Reviews:

No comments

Related manuals for EGSP-130E

Brand: Haier Pages: 6

Brand: Haier Pages: 6

Brand: Haier Pages: 24

Brand: Haier Pages: 12

Brand: Haier Pages: 12

Brand: Haier Pages: 23

Brand: Haier Pages: 12

Brand: Gaggenau Pages: 2

Brand: Asko Pages: 32

Brand: Infiniton Pages: 127

AdoraDish V2000

Brand: V-ZUG Pages: 52

Brand: NEFF Pages: 30

Brand: Hoover Pages: 17

Brand: DELLA Pages: 7

Brand: Smeg Pages: 26

Brand: Progress Pages: 56

Brand: WESCO NAVY Pages: 186

Brand: GE Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands