ROMANA
107
QM2
Intrerupator automat magnetotermic, pentru protectie la suprasarcini si scurtcircuite pe reteaua de alimentare a
motorului P2, cu rearmare manuala.
Setati pe QM1 si QM2 curentul indicat pe placuta motorului.
QS1
Intrerupator de sectionare la reteaua de alimentare.
SA1
Comutator de activare modul electronic
SZ2,
cu ajutorul releului KA1, unde:
Electropompe controlate prin modul electronic
SZ2
Electropompe controlate direct de presetupe
(modul electronic
SZ2
exclus)
SB1
Buton de functionare al electropompei P1 in regim manual cat timp exista impuls.
SB2
Buton de functionare al electropompei P2 in regim manual cat timp exista impuls.
KT1
KT2
Timer de reglare a timpului necesar pentru un cuplu de pornire ridicat. Posibilitate de reglare de la 0,5 la 4 sec.
Setat de constructor în faza de calibrare la 2 sec. (doar pentru E2D 6 M HS).
HL3
Led luminos verde care indica alimentarea electropompei P1
⇒
HL6
Led luminos verde care indica alimentarea electropompei P2
⇒
HL2
Led luminos rosu care se activeaza la interventia dispozitivului de protectie al presostatului de
minim/plutitorului impotriva functionarii pe uscat si presostatului de maxim pentru presiune
P.MAX.
⇒
ALARM
Ref.
Functii (referinte in manual cu schemele anexate)
A
1
-
2
Borne de conexiune pentru plutitorul de control nivel minim (de utilizat numai in instalatii prevazute cu 3
plutitoare de control nivelul apei plus eventual unul de alarma).
Caracteristici de intrare: 5V d. c. 2.5mA cu modul SZ2 inserat.
B
3 - 4
Instalatii cu doua plutitoare (B+C):
borne de conexiune pentru plutitor (control nivel minim/maxim
electropompa P1 si minim electropompa P2) si pentru termostat sau vana de zona pentru circulatoare.
Instalatii cu trei plutitoare (A+B+C):
borne de conexiune pentru plutitor control nivel maxim electropompa
P1; Caracteristici de intrare: 5V d.c. 2.5mA cu modul SZ2 inserat; 24V a.c. 0.5A cu modul SZ2 exclus.
C
5 - 6
Borne de conexiune pentru plutitor control nivel maxim electropompa P2 si termostat sau vana de zona pentru
circulatoare.
Caracteristici de intrare: 5V d.c. 2.5mA cu modul SZ2 inserat; 24V a.c. 0.5A cu modul SZ2 exclus;
N
21 - 22
Borne de conexiune pentru plutitor impotriva functionarii fara apa. In cazul utilizarii indepartati puntea de by-
pass prevazuta standard intre bornele nr. 21 si nr. 22. Caracteristici de intrare: 24V a.c. 40mA.
Comenzile A, B, C, N, R nu necesita conectarea la
deoarece sunt conectate
la circuitul de siguranta PELV (CEI EN 60204-1).
O
23 -
24
Conexiunea (prevazuta standard) pentru selectarea functionarii modulului SZ2 pentru electropompe de drenare;
cu puntea exclusa modulul SZ2 este prevazut in functiune pentru circulatoare si grupuri de presurizare.
P
25 -
26
Borne de conexiune pentru plutitorul de alarma. Caracteristici de contact:
≤
8 Amp;
≤
250V.
Eventualele interventii ale sigurantelor fuzibile ale tabloului nu exclud functia
plutitorului.
Q
31 - 32
Borne de conexiune alarma la distanta pentru semnalizarea interventiei plutitorului de alarma.
Caracteristici de contact:
fara potential
, NA (normal deschis);
≤
8 Amp;
≤
250V.
R
35 - 36
Borne de conexiune pentru presostatul de presiune maxima P.MAX.
In caz de utilizare indepartati puntea de by-pass prevazuta standard intre bornele nr. 35 si nr. 36
Caracteristici de intrare: 24V a.c. 40mA.
L1-N
Cabluri de conexiune electropompa P1/P2 pentru tablouri tip
E2D 2,6 M.
Respectati cu strictete corespondenta prevazuta.
C-A-P
Cabluri de conexiune electropompa P1/P2 pentru tablouri tip
E2D 6 M -
E2D 6 M HS
.
Respectati cu strictete corespondenta prevazuta.
K -K
Intr
are protecţie termică pentru motor.
Summary of Contents for E2D 2,6 M
