ROMANA
110
−
Eventualul plutitor impotriva functionarii fara apa N legat la bornele 21-22 la ambele tipuri de instalatii
blocheaza functionarea electropompelor.
3.
Verificati aspectele mentionate mai sus si utilizand comutatorul ref. SA1 in pozitia
: nu se realizeaza
inversarea automata a ordinii de pornire a celor doua electropompe.
Evitati pornirea instalatiei, actionand asupra intrerupatorului de sectionare
(ref. QS1) cu ambele interupatoare ref. QM1 si QM2 in pozitia I
.
8.7
Instalatie de protectie a grupului (daca este prevazuta)
1.
Protectia se obtine printr-un presostat /plutitor de nivel minim si maxim conectat la bornele ref. N (n°21-22) si la
bornele ref. R (n°35-36).
2.
Pentru a verifica functionarea corecta simulati interventia presostatului/plutitorului de nivel minim si maxim.
Grupul trebuie sa se opreasca si LED-UL LL1 al modulului SZ2 se stinge.
8.8
Instalatia de alarma
1.
Verificati functionarea corecta a plutitorului de alarma legat la bornele ref. P (nr.25-26).
2.
Cu plutitorul de alarma in pozitia ON verificati corecta functionare a alarmei la distanta conectata la bornele
Q (nr.31-32),
tinand cont de faptul ca asa cum este prevazut de serie, contactul nu are potential
.
N.B. : Circuitul de alimentare a instalatiei de alarma trebuie sa fie prevazut cu circuit de siguranta PELV (CEI EN
60204-1). In caz contrar asigurati-va ca cablul de impamantare al plutitorului este conectat la borna
8.9
Utilizarea tabloului pentru a alimenta circulatoarele in linie sau grupurile de
presurizare casnice.
Pentru a predispune functionarea tabloului pentru pompe in-line sau pentru grupuri de presurizare este obligatoriu sa
scoateti puntea O conectata la bornele nr. 23-24.
8.10 Depistare defectiuni E2D 2,6 M - E2D 6 M - E2D 6 M HS
DEFECTIUNI
VERIFICARI (CAUZE POSIBILE)
TIP INTERVENTIE
1.
Unul din cele doua
motoare (P1 si/sau
P2) nu se
alimenteaza.
A.
Au intervenit, intrerupatorul magnetotermic
al tabloului (ref. QM1 sau QM2) sau
intrerupatorul automat diferential al tabloului
de distributie.
B.
Nu este prezenta tensiunea pe bornele L1-N.
C.
A intervenit protectia transformatorului
intern.
D.
A intervenit siguranta fuzibila FU1.
E.
Intrerupatorul ref. KM1 si KM2 vibreaza.
F.
Modulul de schimb SZ2 este defect.
A.
Controlati izolatiile cablurilor electropompei si ale
plutitoarelor. Rearmati intrerupatorul
magnetotermic amplasat pe tabloul de comanda
(ref. QM1 sau QM2) sau cel diferential al tabloului
de distributie.
B.
Verificati cablurile de conectare ale tabloului si
eventuale intrerupatoare sau dispozitive de
sectionare care au intervenit in instalatie.
C.
Deschideti timp de trei minute intrerupatorul
general si apoi inchideti. Pornirea electropompei
exclude avaria. Daca electropompa nu este
alimentata, sau este alimentata temporar,
identificati eventualele scurt – circuite in circuitul
secundar al transformatorului.
D.
Depistati eventuale scurtcircuite ale
trasformatorului si resetati siguranta fuzibila care a
intervenit.
E.
Tensiunea de alimentare este insuficienta.
F.
Aduceti comutatorul SA1 in
si cititi cu
atentie nota
“important”
(par. 8.3.3).
2.
Protectia ref. QM1
sau QM2 intervine.
A.
Rotorul pompei P1 sau P2 blocat.
B.
Timer-ul de reglare timp cuplare la pornire
est reglat peste cele 4 secunde
(numai pentru E2D 6 M HS).
A.
Efectuati operatiunile de intretinere pentru a
debloca rotorul.
B.
Reglati corect timer-ul conform instructiunilor din
ref. KT1-KT2.
3.
Protectia termica
inserata pe bobinele
motorului P1 sau
P2 intervine.
A.
Verificati temperatura ambientului de lucru
al electropompei P1 sau P2.
B.
Rotorul pompei P1 sau P2 blocat sau
astupat.
C.
Verificati starea arborelui rotor al
electropomei P1 sau P2.
A.
Reduceti temperatura lichidului de pompat.
B.
Efectuati intretinerea pentru a debloca rotorul.
C.
Inlocuiti rulmentii pompei P1 sau P2 daca sunt
uzati.
4.
Pompa P1 sau P2
continua sa
pompeze si nu
raspunde
comenzilor externe.
A.
Plutitoarele nu sunt conectate corect la
tablou.
B.
Plutitoarele sunt in avarie.
C.
Intrerupatorul KM1 sau KM2 este defect
(contacte lipite).
D.
Modulul de schimb SZ2 este defect.
A.
Legati corect plutitoarele si controlati functionarea
instalatiei (par.8.3).
B.
Inlocuiti plutitoarele.
C.
Inlocuiti componenta.
D.
Aduceti comutatorul SA1 in
cititi cu
atentie nota
“important”
(par. 8.3.3).
Summary of Contents for E2D 2,6 M
