manualshive.com logo in svg

D-Link JustConnect DNR-4020-16P, User Manual

Share
Download
D-Link JustConnect DNR-4020-16P User Manual Download Page 122

117

D-Link DNR-4020-16P User Manual

Section 3 - Configuration

Alarm In

Enable Alarm

In 

Event Actions

Enable Alarm

Out

Enable Event 

Recording

Detection 

Schedule

Normal State

Port Name 

Camera Alarm

In

Select the channel to configure.

Toggle this to enable or disable Alarm In events and alarms.

Select the event(s) the alarm should trigger from the following 
list:

•  Email: Send an email notification
•  Buzzer: Trigger a buzzer sound
•  Popup Message: Display a notification in a popup window

Trigger a notification on the Alarm Out interface(s).

Toggle to keep a record of alarm events.

Enable or disable the alarm according to a particular schedule.

Specify the normal state of the sensor. A change from this state will 
trigger the alarm.

Designate a name for the sensor.

Click this tab to configure similar settings for sensors connected to 
a camera’s Alarm In interface.

Alarm In

Use this page to enable an alarm when a signal from an external device connected 
to the NVR’s Alarm In interface is detected.

Summary of Contents for JustConnect DNR-4020-16P








































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands