D-Link DVG-7111S User Manual Download Page 48

Page: 48 / 95

DVG-7111S

User’s Manual

ADVANCED

D-Link Systems, Inc.

3-2-1-7 DTMF & PULSE

ADVANCED

→

VoIP

→

DTMF & PULSE

Dial Wait Timeout:

Enter the timeout duration after the user picks up the phone set.

Inter Digits Timeout:

Enter the timeout duration between the intervals of each key pressed. When

exceeding the set timeout duration without entering further digits, the numbers entered will be dialed
out.

Minimum DTMF ON Length (Dial on)/ Minimum DTMF OFF Length (Dial off - between tones):

This

variable is to set the length of DTMF playback.

DTMF Detection Sensitivity:

Select the sensitivity of the telephone keys for the VoIP TA to detect the

DTMF.

DTMF Detection Volume Sensitivity:

Adjust DTMF detect threshold of DTMF volume

DTMF Output Volume:

Adjust the Tx volume of FXS port for DTMF Caller ID or Out of Band DTMF.

FXO Dial Type:

Select dial type as

DTMF

Pulse

for FXO.

Pulse Dial Mark / Space Ration:

Duration and break for pulse dial ration.

Enable Out-of-Band DTMF:

Check the box to set the method of DTMF transmission. RFC2833 or SIP

Summary of Contents for DVG-7111S
































































































Search results

Summary of Contents for DVG-7111S

Reviews:

Related manuals for DVG-7111S

Brands by name

Popular brands

D-Link DVG-7111S, User Manual

Search results

Summary of Contents for DVG-7111S

Reviews:

Related manuals for DVG-7111S

Brands by name

Popular brands