D-Link DVG-7111S User Manual Download Page 20

Page: 20 / 95

DVG-7111S

User’s Manual

SETUP

D-Link Systems, Inc.

SETUP

→

Internet Setup

WAN Link Speed:

Select WAN port link speed.

SETUP

→

Internet Setup

VoIP Connection Interface:

Select a WAN interface for DVG-N5412SP VoIP traffic.

SETUP

→

Internet Setup

Factory Default MAC Address:

The original MAC address of the VoIP Router.

Your MAC Address:

It is left blank as you log-in via the WAN port.

Current MAC Address:

It shows the current MAC Address if you ever used the different MAC address

from Factory Default MAC Address. You can click

Clone

to automatically copy the MAC address of the

Ethernet Card installed in the computer used to configure the device.

Note:

This is only necessary to fill the field if required by your ISP.

SETUP

→

Internet Setup

Click

“Advanced Configuration” for 802.11q/p VLAN tag or dual WAN access configuration.

Summary of Contents for DVG-7111S
































































































Search results

Summary of Contents for DVG-7111S

Reviews:

Related manuals for DVG-7111S

Brands by name

Popular brands

D-Link DVG-7111S, User Manual

Search results

Summary of Contents for DVG-7111S

Reviews:

Related manuals for DVG-7111S

Brands by name

Popular brands