D-Link DVG-7111S User Manual Download Page 24

Page: 24 / 95

DVG-7111S

User’s Manual

SETUP

D-Link Systems, Inc.

Note: Proxy Server Realm

SIP Domain

and

Use Domain to Register

are the parameters provided

by VoIP Service Provider. If you fail to make a call, please contact your VoIP Service Provider.

Bind Proxy Interval for NAT:

Check the box to keep the binding exist by sending packets when the

VoIP TA is behind a NAT and SIP proxy server is not able to keep the binding.

Initial Unregister:

Check the box to send an unregistered message initially by the VoIP TA and then it

will perform a general register process.

Unregister All Contacts:

DVG-N5412SP will fill

“*”(a star) in Contact field in un-register request to

release all registered accounts in this DVG-N5412SP.

Keep SIP Auth:

DVG-N5412SP keeps the last register SIP MD5 authentication information and re-use

it for next register request.

Support Message Waiting Indication (MWI):

It is used to enable/disable Message Waiting Indication.

It is available only when Voice Mail Service is available from the VoIP Service Provider.

Summary of Contents for DVG-7111S
































































































Search results

Summary of Contents for DVG-7111S

Reviews:

Related manuals for DVG-7111S

Brands by name

Popular brands

D-Link DVG-7111S, User Manual

Search results

Summary of Contents for DVG-7111S

Reviews:

Related manuals for DVG-7111S

Brands by name

Popular brands