D-Link DSL-562T User Manual Download Page 17

Page: 17 / 89

DSL-562T ADSL Router User

’

s Guide

Standards Compatibility and Compliance

The DSL-562T complies with or is compatible with the following standards as recognized by their respective
agencies.

•

ITU G.992.2 (G.lite

“

Splitterless ADSL

”

) compliant

•

ITU-T Rec. I.361 compliant

•

RFC 791 Internet Protocol compliant

•

RFC 792 UDP compliant

•

RFC 826 Address Resolution Protocol compliant (ARP) compliant

•

RFC 1058 Routing Information Protocol (RIP) compliant

•

RFC 1213 MIB II for IP compliant

•

RFC 1334 PPP Authentication Protocol compliant

•

RFC 1389 Routing Information Protocol 2 (RIP2) compliant

•

RFC 1483 IP over AAL5/ Bridged Ethernet over AAL5 compliant

•

RFC 1557 Classical IP over ATM (IPoA) compliant

•

RFC 1661 Point to Point Protocol (PPP) compliant

•

RFC 1877 Automatic IP assignment compliant

•

RFC 1994 Challenge Handshake Authentication Protocol compliant

•

Supports RFC 2131 and RFC 2132 DHCP functions including: automatic assignment of IP address, use of
subnet mask and default gateway and provision of DNS server address for all hosts

•

RFC 2364 PPP over ATM compliant (PPPoA) compliant

•

RFC 2516 PPP over Ethernet compliant (PPPoE) compliant

•

RFC 2684 Bridged/Routed Ethernet over ATM compliant

•

IEEE 802.3 compliant

•

IEEE 802.3u compliant

•

IEEE 802.1d compliant

•

IEEE 802.3x compliant

•

Embedded web server support

•

Supports Dynamic Learning

•

Supports Static Routing

•

Supports NAPT for up to 4096 connections

•

Supports DHCP for up to 253 hot connections

•

Supports IGMP

•

Supports ATM Forum UNI 3.1/4.0

•

Supports ATM VCC (Virtual Channel Circuit) for up to eight sessions

•

Supports TELNET and TFTP

•

Supports back pressure for half-duplex

Summary of Contents for DSL-562T


























































































Search results

Summary of Contents for DSL-562T

Reviews:

Related manuals for DSL-562T

Brands by name

Popular brands

D-Link DSL-562T, User Manual

Search results

Summary of Contents for DSL-562T

Reviews:

Related manuals for DSL-562T

Brands by name

Popular brands