D-Link DPN-144DG User Manual Download Page 19 | Manualshive

Page: 19 / 217

background image

DPN-144DG

GPON ONT Dual Band Wireless AC1200

VoIP Gateway with 1 GPON Port, 4 10/100/1000Base-T
Ports, 2 FXS Ports, and 1 USB Port

User Manual

Installation and Connection

Connecting to PC

!

Invisible laser radiation may be emitted from the end of the fiber and/or from

DPN-144DG

.

Take all necessary precautions to avoid unnecessary exposure to this radiation.

PC with Ethernet Adapter

1. Connect an Ethernet cable between any of LAN ports located on the back panel of the

gateway and the Ethernet port of your PC.

2.

To connect via USB modem

: connect your USB modem to the USB port

8

located on the

back panel of the gateway.

!

In some cases you will need to reboot the gateway after connection of the USB modem.

3.

To connect the device to a fiber optic line

: connect the fiber optic cable to the PON port on

the back panel of the gateway. Make sure that center conductor of the cable is inserted
directly into the center of the PON connector. Secure the cable by carefully pushing the fiber
connector onto the PON connector until tight. Be careful not to over-tighten the connector or
you may damage either the cable or the device.

4.

To connect the device to an Ethernet line

: in the web-based interface of the gateway, select

the gateway's LAN port that will be used as the WAN port and create an Ethernet WAN
connection. Then connect an Ethernet cable between an available Ethernet port of the
gateway and the Ethernet line.

!

Please connect the gateway to the ISP's Ethernet line only after setting the WAN port and
creating the Internet connection.

5. Connect a phone cable between an FXS port of the gateway and the phone.
6. Connect the power cord to the power connector port on the back panel of the gateway, then

plug the power adapter into an electrical outlet or power strip.

7. Turn on the gateway by pressing the

POWER ON/OFF

button on its back panel.

8. Wait for several minutes. When the device receives all needed settings, the

PON

LED will

stop blinking and will light solid green. When the Internet connection is established, the

Internet

LED will light solid green.

Then make sure that your PC is configured to obtain an IP address automatically (as DHCP client).

8 It is recommended to use a USB extension cable to connect a USB modem to the gateway.

Page

19

of 217

«
...
17
18
19
20
21
...
»

Summary of Contents for DPN-144DG


























































































































































































































Reviews:

No comments

Related manuals for DPN-144DG

Brand: nedis Pages: 44

Brand: 3onedata Pages: 4

Brand: THOMSON Pages: 90

Brand: Esse-ti Pages: 56

Brand: Pathway connectivity solutions Pages: 14

Brand: Pace Pages: 19

Brand: M-system Pages: 7

Brand: Plugwise Pages: 16

Brand: Linksys Pages: 32

Brand: WePresent Pages: 39

Brand: Xantrex Pages: 38

Communications gateway

Brand: Xantrex Pages: 70

Brand: VOPtel Pages: 49

Brand: Planet Networking & Communication Pages: 77

Power Xpert Meter 2000

Brand: Eaton Pages: 12

Brand: SICK Pages: 105

Brand: RTA Pages: 76

INDeX Media Gateway

Brand: Avaya Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands