D-Link DAP-3662 User Manual Download Page 92

Page: 92 / 94

D-Link DAP-3662 User Manual

Appendix B - Statements

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority

to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

This device and it’s antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in

accordance with FCC multi-transmitter product procedures.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed

and operated with minimum distance 23 cm between the radiator & your body.

FCC NOTICE: To comply with FCC part 15 rules in the United States, the system must be professionally installed to ensure compliance with

the Part 15 certification. It is the responsibility of the operator and professional installer to ensure that only certified systems are deployed

in the United States. The use of the system in any other combination (such as co-located antennas transmitting the same information) is

expressly forbidden.

IC Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this

Summary of Contents for DAP-3662































































































Search results

Summary of Contents for DAP-3662

Reviews:

Related manuals for DAP-3662

Brands by name

Popular brands

D-Link DAP-3662, User Manual

Search results

Summary of Contents for DAP-3662

Reviews:

Related manuals for DAP-3662

Brands by name

Popular brands