D-Link AirPremier DWL-00AP Manual Download

Page: 84 / 84

Technical Support

You can find software updates and user documentation on the D-Link websites.

If you require product support, we encourage you to browse our FAQ section on

the Web Site before contacting the Support line. We have many FAQ’s which

we hope will provide you a speedy resolution for your problem.

For Customers within

The United Kingdom & Ireland:

D-Link UK & Ireland Technical Support over the Internet:

http://www.dlink.co.uk

ftp://ftp.dlink.co.uk

D-Link UK & Ireland Technical Support over the Telephone:

08456 0003 (United Kingdom)

+890 886 899 (Ireland)

Lines Open

8.00am-0.00pm Mon-Fri

0.00am-7.00pm Sat & Sun

For Customers within Canada:

D-Link Canada Technical Support over the Telephone:

-800-36-565 (Canada)

Mon. to Fri. 7:30AM to 9:00PM EST

D-Link Canada Technical Support over the Internet:

http://support.dlink.ca

email: [email protected]

Summary of Contents for AirPremier DWL-00AP





















































































Search results

Summary of Contents for AirPremier DWL-00AP

Reviews:

Related manuals for AirPremier DWL-00AP

Brands by name

Popular brands

D-Link AirPremier DWL-00AP, Manual

Search results

Summary of Contents for AirPremier DWL-00AP

Reviews:

Related manuals for AirPremier DWL-00AP

Brands by name

Popular brands