D-Link AirPremier DWL-00AP Manual Download

Page: 43 / 84

Device Configuration>General

When selecting multiple devices for configuration, some options are unavailable for

configuration as noted(*) below:

• Device Name(*)

: This allows you to change the device name for the selected

access point. You must place a checkmark in the Device Name box to change

the name. This option can only be configured when one access point is selected for

configuration.

• IP address and Subnet Mask(*)

If you’ve selected one device for configuration and

you want to change the IP address of the device, check the IP Address box. You can

then enter an IP address and Subnet Mask for the selected access point. This option

is only configurable when one access point is selected for configuration. To configure

multiple devices with an IP address at one time, please reference the previous page.

• Gateway

: Enter the IP address of your gateway, typically your router address.

• DHCP client

: There is a pulldown menu to select enabled or disabled. When

enabled, the selected device(s) will function as a DHCP client(s). This allows them to

receive IP configuration information from a DHCP server. When disabled, the access

point(s) must have a static IP address assigned to them.

Using the AP Manager (continued)

Summary of Contents for AirPremier DWL-00AP





















































































Search results

Summary of Contents for AirPremier DWL-00AP

Reviews:

Related manuals for AirPremier DWL-00AP

Brands by name

Popular brands

D-Link AirPremier DWL-00AP, Manual

Search results

Summary of Contents for AirPremier DWL-00AP

Reviews:

Related manuals for AirPremier DWL-00AP

Brands by name

Popular brands