D-Link AirPremier DWL-00AP Manual Download

Page: 56 / 84

Using the AP Manager (continued)

Firmware

To upgrade the firmware:

•

Download the latest firmware upgrade from

http://support.dlink.com

to an easy

to find location on your hard drive.

•

Click on the firmware button as shown above.

•

A popup window will appear. Locate the firmware upgrade file and click

Open

IMPORTANT! DO NOT DISCONNECT POWER FROM THE UNIT WHILE THE

FIRMWARE IS BEING UPGRADED.

You can upgrade the firmware by clicking on

this button after selecting the device(s).

You can customize the basic System Settings for

the DWL-00AP by clicking on this button.

System Settings

• Access Password

: This sets the admin password for

the selected device(s).

• Auto Refresh

: This setting allows you to enable auto

refreshing of the network device list. By default this option

is disabled. If you choose to enable it, you must enter the

refresh interval in seconds.

All other settings on this screen should

be left at the default setting.

Summary of Contents for AirPremier DWL-00AP





















































































Search results

Summary of Contents for AirPremier DWL-00AP

Reviews:

Related manuals for AirPremier DWL-00AP

Brands by name

Popular brands

D-Link AirPremier DWL-00AP, Manual

Search results

Summary of Contents for AirPremier DWL-00AP

Reviews:

Related manuals for AirPremier DWL-00AP

Brands by name

Popular brands