D-Link AirPremier DWL-00AP Manual Download

Page: 22 / 84

Using the Configuration Menu (continued)

Home > LAN

LAN is short for Local Area Network. This is considered your internal network. These

are the IP settings of the LAN interface for the DWL-00AP. These settings may be

referred to as private settings. You may change the LAN IP address if needed. The LAN

IP address is private to your internal network and cannot be seen on the Internet.

Click

Apply

to save the changes.

Get IP From-

Select

Static (Manual)

Dynamic (DHCP)

as the method you

will use to assign an IP address to the DWL-00AP.

Apply-

Default Gateway-

This field is optional. Enter in the lP address of the gateway

on your network.

Subnet Mask-

The subnet mask of the LAN interface.

The default subnet mask is

255.255.255.0

IP Address-

The IP address of the LAN interface. The default IP address

is:

192.168.0.50

Summary of Contents for AirPremier DWL-00AP





















































































Search results

Summary of Contents for AirPremier DWL-00AP

Reviews:

Related manuals for AirPremier DWL-00AP

Brands by name

Popular brands

D-Link AirPremier DWL-00AP, Manual

Search results

Summary of Contents for AirPremier DWL-00AP

Reviews:

Related manuals for AirPremier DWL-00AP

Brands by name

Popular brands