D-Link AirPremier DWL-00AP Manual Download

Page: 29 / 84

Using the Configuration Menu (continued)

Advanced > DHCP Server > Current IP Mapping List

Current DHCP Dynamic

Pools-

Binding MAC address-

Assigned IP address-

Lease Time-

Current DHCP Static Pools-

These are IP address pools to which the DHCP server

function has assigned static IP addresses.

Binding MAC address-

Assigned IP address-

This screen displays information about the current DHCP dynamic and static IP address

pools. This information is available when you enable the DHCP function of the DWL-00AP

and assign dynamic and static IP address pools.

The MAC address of a device on the network that is

within the DHCP dynamic IP address pool.
The current corresponding DHCP-assigned dynamic

IP address of the device.

The length of time that the dynamic IP address will

be valid.

The MAC address of a device on the network that is within

the DHCP static IP address pool.

The current corresponding DHCP-assigned static IP

address of the device.

These are IP address pools to which the DHCP

server function has assigned dynamic IP addresses.

Summary of Contents for AirPremier DWL-00AP





















































































Search results

Summary of Contents for AirPremier DWL-00AP

Reviews:

Related manuals for AirPremier DWL-00AP

Brands by name

Popular brands

D-Link AirPremier DWL-00AP, Manual

Search results

Summary of Contents for AirPremier DWL-00AP

Reviews:

Related manuals for AirPremier DWL-00AP

Brands by name

Popular brands