d.gen TELEIOS HEXA Operator'S Manual Download Page 11

Page: 11 / 65

TITLE

OPERATOR MANUAL

PAGE

PRINTERS

TELEIOS HEXA

VERSION

2017JAN23/1

OUT OF

REVISED BY

MUNOZ, ANTONIO

[email protected]

FOR THE USER

d·gen International, Inc. - COMPANY PRIVATE (LEVEL 1)

NOT TO BE DISCLOSED TO UNAUTHORIZED PERSONS – PROHIBIDA SU DIVULGACIÓN A PERSONAS NO AUTORIZADAS

DO NOT REPRODUCE WITHOUT AUTHORIZATION – NO REPRODUCIR SIN AUTORIZACIÓN

BIG INK SYSTEM

Cover.

Buzzer can be heard if this cover is opened. Cover normally closed when using the printer.

Lid and ink filter.

We suggest to pour the ink on the filter. Also, is suggested not to close the lid totally to let the air
flow in while the cylinder is getting empty.

Cover switch.

This device activated the buzzer when the cover is opened for refilling the inks.

Ink level photo sensor.

This photo sensor measures the ink level with a laser beam. Keep this area always free of ink.

Summary of Contents for TELEIOS HEXA


































































Search results

Summary of Contents for TELEIOS HEXA

Reviews:

Related manuals for TELEIOS HEXA

Brands by name

Popular brands

d.gen TELEIOS HEXA, Operator'S Manual

Search results

Summary of Contents for TELEIOS HEXA

Reviews:

Related manuals for TELEIOS HEXA

Brands by name

Popular brands