manualshive.com logo in svg

d.gen TELEIOS HEXA, Operator'S Manual

Share
Download
d.gen TELEIOS HEXA Operator'S Manual Download Page 39

 

TITLE 

OPERATOR MANUAL 

PAGE 

PRINTERS 

TELEIOS HEXA 

39 

VERSION 

2017JAN23/1 

OUT OF 

REVISED BY 

MUNOZ, ANTONIO 

[email protected] 

63 

 

FOR THE USER 

d·gen International, Inc. - COMPANY PRIVATE (LEVEL 1) 

NOT TO BE DISCLOSED TO UNAUTHORIZED PERSONS – PROHIBIDA SU DIVULGACIÓN A PERSONAS NO AUTORIZADAS 

DO NOT REPRODUCE WITHOUT AUTHORIZATION – NO REPRODUCIR SIN AUTORIZACIÓN

 

 

Note 

Only possible to change the direction of rotation having the take-up in the OFF position. Turn off the take-
up. Change direction and then turn on the take-up again. 

 

9 

At this point you may press the right arrow key “ON/OFF” to switch on the heater. The green LED at 
the control panel will turn on. To change the SV value, you may press the ENTER button. The 
underscore will change into a cursor. Suppose I want to change from 175 to 190°C. 

 

 

 

10 

Change the 7 into an 9 by pressing the up-arrow key. Then move the underscore to the right by 
pressing the right arrow key. Change the 5 into an 0 by pressing the down arrow key. Press the 
ENTER button to validate the new change. The underscore will change into a cursor again. 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for TELEIOS HEXA


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands