manualshive.com logo in svg

d.gen TELEIOS HEXA, Operator'S Manual

Share
Download
d.gen TELEIOS HEXA Operator'S Manual Download Page 34

 

TITLE 

OPERATOR MANUAL 

PAGE 

PRINTERS 

TELEIOS HEXA 

34 

VERSION 

2017JAN23/1 

OUT OF 

REVISED BY 

MUNOZ, ANTONIO 

[email protected] 

63 

 

FOR THE USER 

d·gen International, Inc. - COMPANY PRIVATE (LEVEL 1) 

NOT TO BE DISCLOSED TO UNAUTHORIZED PERSONS – PROHIBIDA SU DIVULGACIÓN A PERSONAS NO AUTORIZADAS 

DO NOT REPRODUCE WITHOUT AUTHORIZATION – NO REPRODUCIR SIN AUTORIZACIÓN

 

 

3 

The green LCD display will show the welcome screen. 
It is possible to control the machine in AUTO or MANUAL mode. For the correct functioning of the 
fixation unit we recommend to leave the settings a shown in the image below. By pressing the 
ENTER button the next main screen will be displayed. 

 

 

 

4 

Since this printer doesn’t have the ability to run the fixation unit in AUTO mode, we suggest to 
change it to MANUAL mode. By pushing the AUTO/MANUAL button is possible to make the fixation 
unit to work under MANUAL conditions. You can see all the left arrow will change from A to M. 

 

 

 

Caution 

Please note that this printer doesn’t have the ability to send the carriage idle signal to the fixation unit. 
Therefore, we strongly ask the user to 

avoid using AUTO mode

. 

 

Summary of Contents for TELEIOS HEXA


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands