manualshive.com logo in svg

d.gen TELEIOS HEXA, Operator'S Manual

Share
Download
d.gen TELEIOS HEXA Operator'S Manual Download Page 23

 

TITLE 

OPERATOR MANUAL 

PAGE 

PRINTERS 

TELEIOS HEXA 

23 

VERSION 

2017JAN23/1 

OUT OF 

REVISED BY 

MUNOZ, ANTONIO 

[email protected] 

63 

 

FOR THE USER 

d·gen International, Inc. - COMPANY PRIVATE (LEVEL 1) 

NOT TO BE DISCLOSED TO UNAUTHORIZED PERSONS – PROHIBIDA SU DIVULGACIÓN A PERSONAS NO AUTORIZADAS 

DO NOT REPRODUCE WITHOUT AUTHORIZATION – NO REPRODUCIR SIN AUTORIZACIÓN

 

 

 

8 

Then make it go through the first rubber roller. Make sure the media is aligned by ensuring that the 
distance between the edge of the media and the printer’s frame is the same at all points. 

 

 

 

9 

Send the media to the front (by switching to AUTO BACKWARD and pressing the forward button in 
the touch panel) so the other operator at the other side can hold the media. Having the media being 
hold from the other side is time to lower the press roller. 

 

 

 

Summary of Contents for TELEIOS HEXA


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands