d.gen TELEIOS HEXA Operator'S Manual Download Page 37 | Manualshive

Page: 37 / 65

background image

TITLE

OPERATOR MANUAL

PAGE

PRINTERS

TELEIOS HEXA

37

VERSION

2017JAN23/1

OUT OF

REVISED BY

MUNOZ, ANTONIO

[email protected]

63

FOR THE USER

d·gen International, Inc. - COMPANY PRIVATE (LEVEL 1)

NOT TO BE DISCLOSED TO UNAUTHORIZED PERSONS – PROHIBIDA SU DIVULGACIÓN A PERSONAS NO AUTORIZADAS

DO NOT REPRODUCE WITHOUT AUTHORIZATION – NO REPRODUCIR SIN AUTORIZACIÓN

Caution

Before regulating values, we strongly suggest the user to check first under which conditions is the fixation
unit working in. Either in AUTO or MANUAL mode.

Note

We suggest the user to set a HEATER OV value greater than 40% in order not to have the fixation unit
turning ON/OFF many times in a short period of time.

Note

We suggest a SV of 175°C for most fabrics. Note that all fabrics are not the same. Please contact the
fabric manufacturer for more information regarding the recommended temperature for fixing.

Note

Note that some printers are not provided with HEATER 2 (rubber heater located in the printing table for
extra drying). Ask your local dealer if your machine is provided with HEATER 2 or not.

Note

We suggest the user to keep low torque and speed values at the take-up unit to avoid inverter errors and
prevent the inductive motor and power clutch from overheating.

Note

Suction cannot be turned ON manually under AUTO mode conditions.

«
...
35
36
37
38
39
...
»

Summary of Contents for TELEIOS HEXA


































































Reviews:

No comments

Related manuals for TELEIOS HEXA

Brand: Zeka Pages: 54

NEFAX - 691 B/W Laser

Brand: NEC Pages: 20

Brand: Canon Pages: 21

Brand: Canon Pages: 23

Brand: Lanier Pages: 6

Brand: SII Pages: 85

Brand: Ricoh Pages: 162

Brand: Star Micronics Pages: 194

Brand: Lanier Pages: 140

Brand: Lexmark Pages: 2

JT-H200PR Series

Brand: Panasonic Pages: 2

Jetwriter KX-CL500

Brand: Panasonic Pages: 1

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 29

Jetwriter KX-CL500

Brand: Panasonic Pages: 32

Jetwriter KX-P6100

Brand: Panasonic Pages: 44

AP10 - Thermal Dye Sublimation Photo Printer

Brand: Panasonic Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands