Cygnus Cygnus 2 Operating Manual Download Page 26

Page: 26 / 65

Cygnus 2+ Operating Manual

M5-CYG2P-M-01_Iss6.doc

When a thickness measurement is

displayed the display also shows the

Measurement Mode and the Units.

SE = Single Echo mode

EE = Echo-Echo mode

ME = Multiple Echo mode

Echo Indicators in Multiple Echo Mode

Should the gauge be unable to detect a stable multiple echo signal

it displays an Echo indication to help the operator locate a suitable

position.

1 Bar Flashing:

No echoes detected

1 1 Bar Flashing:

Only 1 echo detected

2 1 Bar Flashing:

Only 2 echoes detected

3 1 Bar Flashing:

3 echoes detected but they are not

matched

To help obtain a multiple echo reading the operator should

continue to move the probe around to locate a suitable reflector,

using a slight rocking motion.

Measurement Stability Indication in SE & EE Modes

To help indicate when a Single Echo or Echo-Echo measurement is

stable – and thus probably reliable – the gauge changes the

thickness measurement number from Hollow to Solid when the

measurement has been stable for 2 consecutive seconds.

When measuring using Single Echo or Echo-Echo mode once you

have a measurement keep the probe still and wait for the gauge to

signal a “stable reading”.

Summary of Contents for Cygnus 2


































































Search results

Summary of Contents for Cygnus 2

Reviews:

Related manuals for Cygnus 2

Brands by name

Popular brands

Cygnus Cygnus 2, Operating Manual

Search results

Summary of Contents for Cygnus 2

Reviews:

Related manuals for Cygnus 2

Brands by name

Popular brands