Cygnus Cygnus 2 Operating Manual Download Page 55

Page: 55 / 65

M5-CYG2P-M-01_Iss6.doc

Cygnus 2+ Operating Manual

12.

Information

Technical Specifications

Cygnus M5-C2P

Technical Specifications

General Attributes
Size

84 mm x 130 mm x 35 mm (W x H x D)

(3.3 in x 5.1 in x 1.4 in)

Weight

Gauge with batteries 300 g (10.5 oz.)

Power Supply

3 x AA / R6 Batteries.

Probe Sockets

2 x Lemo 00

Operating Temperature Range -10°C to +50°C (14°F to 122°F)
Storage Temperature Range

-10°C to +35°C (14°F to 95°F)

Battery Operation Time

Approximately 10 hrs. continuous measurement with fully

charged Duracell Alkaline LR6 batteries.

Battery Voltage Range

Min 3.0 V dc, Max 4.5 V dc

Battery Type

AA Size. LR6 Alkaline / HR6 NiMH.

Low Battery Indication

Battery level indication on display with low battery warning

message.

PRF

N/A

Monitor Outputs

N/A

Through Coating

Measurements

Multiple-Echo mode with Single element 0° probe;

•

Through coating measurement for coatings up to 3 mm

thick as standard depending on coating velocity.

•

Deep Coat mode provides ability to measure through

thicker coatings depending on coating material.

Echo-Echo mode with Twin element probe;

•

Through coating measurement for coatings up to 1 mm

thick as standard depending on coating velocity.

Materials

Sound velocity from 1000 m/s to 9000 m/s

[0.0390 in/us to 0.3543 in/us]

Summary of Contents for Cygnus 2


































































Search results

Summary of Contents for Cygnus 2

Reviews:

Related manuals for Cygnus 2

Brands by name

Popular brands

Cygnus Cygnus 2, Operating Manual

Search results

Summary of Contents for Cygnus 2

Reviews:

Related manuals for Cygnus 2

Brands by name

Popular brands