Cygnus Cygnus 2 Operating Manual Download Page 8

Page: 8 / 65

Cygnus 2+ Operating Manual

M5-CYG2P-M-01_Iss6.doc

Cygnus Instruments

Cygnus Instruments Limited, founded in 1983,

were pioneers in the development of the Digital

Ultrasonic Multiple-Echo Technique used for

measurement through coatings. This has long

been the standard required to ensure that

accurate measurements are taken without the

need to first zero the gauge or remove any

coatings.

Our philosophy is to work closely with each of our customers to

provide a range of products specifically for each application.

Cygnus Ultrasonic Thickness Gauges are designed to be simple to

use and to withstand the harsh environments that they are

intended for. We have built up an enviable reputation with our

customers in over 45 countries around the world.

Summary of Contents for Cygnus 2


































































Search results

Summary of Contents for Cygnus 2

Reviews:

Related manuals for Cygnus 2

Brands by name

Popular brands

Cygnus Cygnus 2, Operating Manual

Search results

Summary of Contents for Cygnus 2

Reviews:

Related manuals for Cygnus 2

Brands by name

Popular brands