Cygnus Cygnus 2 Operating Manual Download Page 3

Page: 3 / 65

M5-CYG2P-M-01_Iss6.doc

Cygnus 2+ Operating Manual

Contents

1. Important Notice .............................................................. 6
2. Introduction ...................................................................... 7

Cygnus 2

Thickness Gauge ....................................................7

Cygnus Instruments ...............................................................8

Gauge Kit Contents ................................................................. 9

Basic Gauge Kit .....................................................................9

Kit supplied with Single Element Probe ......................................9

Kit supplied with Twin Element Probe ........................................9

3. Gauge Preparation .......................................................... 10

Fitting the Batteries ............................................................. 10

Connecting the Probe ........................................................... 11

Fitting the Hand Strap or Belt Clip .......................................... 12

Fitting the Neck Strap .......................................................... 13

4. Selecting the Right Probe ................................................ 15

Measuring Metals ................................................................. 15

Measurement Modes Explained and Compared ......................... 16

Multiple Echo Mode (ME) (Mode 3) ....................................... 16

Single Echo Mode (SE) (Mode 2) ......................................... 16

Echo-Echo Mode (EE) (Mode 3) ........................................... 17

Measuring Non-Steels .......................................................... 17

Measuring Non-Metals .......................................................... 18

Single Element Probes and Protective Membranes ..................... 18

Summary of Cygnus Probes .................................................. 21

Twin Element probes ......................................................... 21

Single Element probes ....................................................... 21

The ‘Probe Type’ Code ....................................................... 22

5. Gauge Operation ............................................................. 23

Gauge Controls ................................................................... 23

Turning the Gauge On .......................................................... 24

Turning the Gauge Off .......................................................... 24

Automatic Power Off .......................................................... 24

‘No Probe’ Message .............................................................. 24

Taking Thickness Measurements ............................................ 25

Zeroing the Probe (twin element probes) .............................. 25

Taking the Thickness Measurement...................................... 25

Echo Indicators in Multiple Echo Mode .................................. 26

Summary of Contents for Cygnus 2


































































Search results

Summary of Contents for Cygnus 2

Reviews:

Related manuals for Cygnus 2

Brands by name

Popular brands

Cygnus Cygnus 2, Operating Manual

Search results

Summary of Contents for Cygnus 2

Reviews:

Related manuals for Cygnus 2

Brands by name

Popular brands