CyberResearch STE 1xGTx Series User Manual Download Page 53

Page: 53 / 198

CyberResearch

Panel PCs

STE 1xGTx Series

3.3 Package Contents

NOTE:

If any components listed in the checklist below are missing, do not

proceed with the installation. Contact a CyberResearch sales engineer

immediately via our website

www.cyberresearch.com

, by phone: (203)

643-5000, or e-mail:[email protected].

The STE 1xGTx is shipped with the following components (many of the components listed

below come pre-installed):

Quantity

Item and Part Number

Image

1 STE

1xGTx

Hard drive bracket

IDE cable (40-pin to 40-pin)

IDE cable (44-pin to 44-pin)

1 Jumper

pack

Wall mounting kit

CyberResearch, Inc

25 Business Park Drive

P: (203) 643-5000; F: (203) 643-5001

Branford, CT USA

www.cyberresearch.com

Summary of Contents for STE 1xGTx Series























































































































































































Search results

Summary of Contents for STE 1xGTx Series

Reviews:

Related manuals for STE 1xGTx Series

Brands by name

Popular brands

CyberResearch STE 1xGTx Series, User Manual

Search results

Summary of Contents for STE 1xGTx Series

Reviews:

Related manuals for STE 1xGTx Series

Brands by name

Popular brands